gbs 8200 3d models
189 3d models found related to gbs 8200.thingiverse
Housing for the well known GBS 8200 video converter. The housing is designed for the HDMI variant available at e.g. AliExpress: https://de.aliexpress.com/item/32860218072.html Additional parts for assembly 4 x M3 * 18 flat head screws Since gbs...
thingiverse
For use with gbs-control: https://github.com/ramapcsx2/gbs-control HDMI Output: - Buy a VGA to HDMI adapter like this https://www.ebay.com/itm/193308585503 3D Print: - Measure the dimensions of your GBS-8200 and compare them to the one in the...
prusaprinters
přidat změnu barvy filamentu ve vrstvě, kdy se tisknou písmena na tlačítkách.V případě zpětné vazby mi prosím napište do komentářů k modelu. ===== EN (used translator)=====This is a complete box for the GBS-8200 converter. </p><p> If you...
thingiverse
I created this mount to easily attach the S15351 Clock Gen to the heatsink of the GBS 8200. ... It's a pretty tight fit.
thingiverse
An easy enclosure for the GBS 8200 v4.0 CGA/EGA/YUV to VGA converter board. Print the top section standing on end, with the vent lines running up/down without supports. ...Print Settings Printer: Reach3dprinters.com ...
cults3d
Enclosure for the GBS-8200 or GBS-8220, 15KHz RGB/VGA to VGA upscaler board. The front and back are made as panels. This makes it easier to modify them, without having to modify the entire enclosure. The 8200 model only has one VGA output whereas...
thingiverse
Enclosure for the GBS-8200 or GBS-8220, 15KHz RGB/VGA to VGA upscaler board. The front and back are made as panels. This makes it easier to modify them, without having to modify the entire enclosure. The 8200 model only has one VGA output whereas...
thingiverse
You will need - 2x M4 x 10 mm screw with nut (for SCART connector) - 2x M3 x 10 mm screw (for HDMI output unit) - 2x M3 x 6 mm screw (for HDMI output unit clamp) - 4x M3 x 35 mm screw (for housing) - 2x M3 x 5 mm hex spacer (male) (for attachment of...
thingiverse
For assembly you can screw down the GBS-8200 as in the original design and the case pretty much still just snaps together and stays reasonably well. ...However, the tabs I added also give you a place to add glue where it won't be visible from the...
thingiverse
This is a case designed only for a GBS-8200 video converter board, if you want to use it for GBS-8220 then you need to modify provided files to include additional hole for second VGA connector. This is possible as also IGES files are included within...
youmagine
... screws. Alternatively, smaller and/or self-tapping fasteners might be a easy solution. The GBS-8200 has applications for converting video signals from arcade machines, old consoles and personal computers or legacy machine controls. ...YMMV.
thingiverse
My version of GBS Control case for GBS 8200 and two sizes of ESP8266 modules, plus RGBS BNC connectors. The two sizes of the ESP8266 module supported are: 48 x 25mm 58 x 31mm Please choose the corresponding one when you print. Project is...
prusaprinters
My version of GBS Control case for GBS 8200 and two sizes of ESP8266 modules, plus RGBS BNC connectors. The two sizes of the ESP8266 module supported are: 48 x 25mm 58 x 31mm Please choose the corresponding one when you print. Project is put together...
prusaprinters
GBS 8200 RGB to VGA Converter Box extended to the right so it can fit a NodeMCU ESP8266 chip to use with the gbs-control custom firmware. ...Also room for a 6pin DIN sock and a switch which I use to turn off the CFW if required</p><p>This was originally...
thingiverse
This is a remix of the GBS-8200 case created by the user with the nickname "stepmotor" on the Russian zx-pk.org forum. The case consists of 2 halves and a button that operates 4 push-in switches on the board. I am also providing the case's parts...
prusaprinters
GBS 8200 RGB to VGA Converter/Upscaller Box. Two holes at the back: one to allow for an alternate power cord (I use a USB power source) and adding the possibility of mounting a micro USB connector PCB; second hole for an input cable (I use Scart...
thingiverse
Adapted my remixed box, extending it to the right so it can fit a NodeMCU ESP8266 chip to use with the gbs-control custom firmware. ...Also room for a 6pin DIN sock and a switch which I use to turn off the CFW if required
thingiverse
Add the wiring for the NodeMCU and the Clock Generator to the GBS side, but don't connect them yet. First screw the controllers to the sidepanels. Make sure you have wires coming from the breakout boards and then slide them into place on the...
prusaprinters
(Print "FrontPanel_input_noSCART" instead of "FrontPanel_input") If you connect Component or VGA, you can use a SCART breakout to pass through audio in a clean way, without ever having to swap the plug on the back. Last, you'll need 8mm M3 hex bolts,...
thingiverse
This is a housing for a GBS 8200 V5 (2017) "Yellow Button" Version with ESP8266, Sync Stripper, SCART and Stereo RCA Chinch.
thingiverse
It's a remix of TheJeffChen's GBS Control Case for GBS 8200 with SCART input and place for HDMI output. This is my first attempt at 3D "modeling" so no guarantees. ...I think everything applies to this modell that applies to the authors.
prusaprinters
GBS-8200 RGB to VGA Video Converter Board Case with 6pin DIN & Wemos D1 Mini WifiDesigned to house the Wemos D1 Mini to use with the customer firmware https://github.com/ramapcsx2/gbs-controlCut-outs for all the connectors including micro USB for...
thingiverse
GBS-8200 RGB to VGA Video Converter Board Case with 6pin DIN & Wemos D1 Mini Wifi Designed to house the Wemos D1 Mini to use with the customer firmware https://github.com/ramapcsx2/gbs-control Cut-outs for all the connectors including micro USB for...
thingiverse
GBS-8200 RGB to VGA Video Converter Board + SCART Case Remix adding housing for a SCART plug. This is the PCB mounted right angle version which clips nicely into the housing with the pins exposed so these can be attached to the wires as required. ...
thingiverse
Took design from Tom_DD and modified it to have scart input on top and audio output from scart. Also cleaned up some of the circles. Should work fine but tell me how it goes. ...Will update when I'm able to test it saturday.
thingiverse
Remixed bottom of the case to add two additional holes at the back. One to allow for the alternate power cord (I use a USB power source) and adding the possibility of mounting a micro usb connector PCB. Second hole for an alternate input cable (I use...
thingiverse
Modified Top Cover to add a DB9 port for use with a wired remote on an Arcade Cabinet.
thingiverse
Habe das Design an meine Bedürfnisse angepasst da das V5.1 Board nicht passte. ... I adapted the design to my needs because the V5.1 board did not fit.
thingiverse
This is a basic case for the GBS 8200 scaler board modified with GBS Control (https://github.com/ramapcsx2/gbs-control/). It uses four heat-set inserts for the M3 (5mm lenght) case screws. It is easy to print (no supports) and very sturdy if printed...