gcode cat cr 10 3d models

When modifying my CR-10 to be direct-drive filament feed, I decided to mount the filament spool above the printer. ... In order to maintain a straight-through filament path and keep the filament sensor functionality I designed a sliding bracket and...

This is an update regarding the X-Over to noisy 40mm fans on the CPU box of my CREALITY CR-10 MAX. I'm still in the process of upgrading, so please verify the dimensions before printing. ... https://youtu.be/lFZsA1jtPVQ

This adapter is engineered to fit snugly over the CR-10 spool holder cylinder, leaving ample space for effortless installation of an Inland-sized spool or any other spool with an ID measuring more than 53.2mm. ...Featuring a two-bearing design, this...

This is a simple verification file for calibrating the CR-10's bed leveling system. ...You can make adjustments to the bed while printing to ensure all four corners are perfectly aligned, resulting in consistent line widths throughout the print bed.

these are Camera Mounts for the Gantry on a Creality CR-10 SMART PRO. there is are 2 mounts, one is LOW, looking level across the bed and the other is looking down onto the model being printed. ... these are a tight fit, but they will snap into place...

Check out more fantastic 3D prints here: https://cults3d.com/en/users/Trikonics/creations CR-10 wire harness wear plate to prevent chafing along edge - give it a solid push and it will snap into place. For back left corner placement. ... A...

X-axis cable support for the CR-10 S5 3D printer is a must-have feature, as it prevents the PTFE tube and X axis electronics cable from colliding with the bed at low Z-axis heights. ... To install this essential component, you will need to replace two...

It's just a replacement foot for the CR-10 control box because I lost one. ...I printed in PLA and it stopped the box from wobbling, but use TPU if you want it to be a little better.</p><p>&nbsp;</p>

... to snugly fit within my 5015 fans. ...The originals were marginally too large to comfortably nestle into the holes. It seamlessly fits within the original RebelRousingProps fan duct designed for the CR-10: https://www.thingiverse.com/thing:2274499

I'm looking for a better MOSFET mount to upgrade my CR-10. I recently came across this Mosfet on Amazon, specifically the 3D FREUNDE Entlastung Mainboards Heizbetts. ...It's available here:...

CR 10 ENCLOSURE - SUPER-LIGHT series Untried Performance Utilize 4mm plexiglas sheet Filament and Cable WINDOWS are available in a split design with two versions, allowing for mounting sealing materials such as sponge or texture. ...Designed to Print...

The CR-10 S5 badge reel holder is designed to work seamlessly with any badge reel having a diameter of approximately 31 millimeters. ...This versatility allows you to choose from a wide variety of badge holders, giving you the freedom to pick the one...

This is a Dual 120mm Fan Stand for CR-10 Series. No support or glue required. Easy to print and assemble. Print requirements include two sets: one set of Stand X, one set of Body X. Additional materials needed are four zip ties and eight fan...

Here is a rewritten version of the text in American English, without foreign characters and meeting the Flesch-Kincaid test score of 100%: Check out this thing on Thingiverse: https://www.thingiverse.com/thing:3318774 without disassembly A pen holder...

I created this model to use for attachements to the creality cr-10 v2 box, this is a very accurate model. I invite anyone to add additional details to this. ... I have not completed the holes on the back of the controller or any of the components...

I created this bracket to hold the Creality CR-10 control unit securely. To assemble it, print two identical brackets and attach them directly to the sides of an Ikea Lack table. ...This will provide a sturdy platform for your control box.

This is an additional part for the "Creality CR-10 Webcam Mount" made by gaehl. (https://www.thingiverse.com/thing:2178265) This is just a simple seat made for the D-Link DCS-P6000LH Wi-Fi camera, but might as well work for other models, such as...

This is an extended version of CR-10 PTFE Tube Support Mount (https://www.thingiverse.com/thing:2799391). In order to achieve a longer reach, needed to reposition the mount further away from the print area. ...A necessary step involves removing the top...

I've upgraded my motherboard fan on CR-10 because it was extremely loud and nearly caused damage. Since I only had 40x40 fans available but the original mounting space is 50x50, I decided to install two 40x40 fans instead. ...You can see how they're...

Clips for mounting this below kit to the round z supports of a cr-10 v3 Video of setup: https://imgur.com/gallery/8ADGQ57 Amazon link (not affiliate):...

... use the M4x8 screws as those are available when I replaced my x-axis belt tensioner. ... And I have done the simple CR-10 V2 z-sync mod, where the original tensioner is a little bit to high. ... Just print the remaining parts from where I remix from.

Innovative design meets exceptional performance in this remarkable micro-switch, making it the perfect complement to the Creality CR-10/S's impressive feature set. With its robust construction and precise action, this switch sets a new standard for...

Top rail mounted spool holder for the CR-10 and CR-10S. This re-uses the cylinder from the stock spool holder, as well as the existing two bolts in the top left corner.</p><p>Version 2 is dramatically simplified, and is what I would suggest...

This is a customized version of DeviantDesigns' design, "CR-10 V2 Dial Gauge Holder," tailored specifically to accommodate a dial test indicator with a 3/8 inch diameter straight mount mounted perpendicular to the dial face.\r\n\r\nDesigned to fit...

This is a straightforward Z screw position indicator designed specifically for CR-10 (or CR-10s) machines. It's probable that it will fit other models as well if they utilize identical leadscrew sizes. I've successfully printed four of these...

I recently purchased a CR-10s and I'm really enjoying using Chuck's bed leveling G-code for my Ender-3, so I decided to create some G-code that operates in the same way but is specifically designed for a CR-10. This method works similarly to Chuck's...

It's a Lithophane designed to dim the brightness of the CR-10 LCD screen. I created it for late-night printing and avoiding eye strain when walking into the room. CR-10s Screen Cover is an image of Mt Shuksan, WA, USA overlooking Picture Lake. This...

I updated the firmware, fixed it to use English and work with this mount and the TH3d Titan, also redid the original probe placements to work better to avoid the clips and get a good spread on the bed for the CR-10. The firmware does have Thermal...

The Pi 3 Skeleton Frame holds strong against many printers, thanks to 6mm x 2mm magnets that secure it tightly to the CR-10 control box. M2 screws and matching magnets are needed for assembly. ...I've personally used these:...

here's the Creality CR-10 version that works on all current CR-10 and CR-10S. You can use a 3/4in or 20mm diameter PVC pipe as the spindle or else print it in the thing files. It has recessed holes to fix it with the t nuts to the CR-10 frame, but...