geeetech a10m vs a20m 3d models

pécialement conçu pour une Geeetech a20m/a20 test de 9 points pour vérifier le niveau du plateau 255x255 specially designed for a Geeetech a20m/a20 9-point test to check the level of the bed 255x255

Address the cable issues that Geeetech introduced in the A10M and A20M To achieve these upgrades, I need five key components: 1. A plate that sits above the control board, using a 60mm fan to cool it down, along with holders for two LM2596 modules -...

A foot holder for the Geeetech A20M to prevent it from sliding sideways. ...It is secured with 2x M3 screws plus a washer.

... length 15mm and two M3 nut for fixing on the 40x20 profile the fixing underneath takes an existing hole. If you prefer a version with threaded rod, here is the link : https://cults3d.com/en/3d-model/various/renfort-chassis-geeetech-a20m-seb86

Designed to convert the stock Geeetech A20M extruder for a more reliable and user friendly direct drive hot end. With mounts for a blower fan and 3DTouch bed leveling sensor! ... 2 files available, with and without 3DTouch mounts!

A custom-made adapter is being designed to securely hold spools measuring 50mm in diameter and 78mm in width, allowing them to be mounted onto a holder that has a diameter of 32mm and a width of 73mm - similar in design to my Geeetech A20M. ...The...

Hello :) I made dampers for the Geeetech A20M printer. The dampers are support free but for the socket you need one in the middle. ... Happy printing everyone :) Have a look on my Instagram to see what i'm doing as well: instagram.com/lorenzo_van_3d

An adapter to put spools with an inside diameter of 50mm and a width of 78mm onto a holder with a diameter of 32mm and a width of 73mm (like my Geeetech A20M). ...The spools cannot fall off on either side.

An adapter to put spools with an inside diameter of 50mm and a width of 78mm onto a holder with a diameter of 32mm and a width of 73mm (like my Geeetech A20M). ...The spools cannot fall off on either side.

So this is an easy little remix, I just changed the mount a bit because I've got a Geeetech A20M and didn't have anywhere to bolt the holder, so I made it snap into the front rail. There's a small dimple on it for some reason, but it doesn't hurt...

Designed for the Geeetech A20M, this part is manufactured to hold a direct drive extruder, blower fan and 3D touch bed leveling sensor. Converting the 2 in one out bowden extruder to a more reliable and user frindly direct drive system! Support is...

Here's my first iteration of the purge bucket for the Geeetech A20M. Installing this along with the tool changing script, which I've tested on Simplify3D only, will allow the purge to happen within the bucket instead of the printer printing a purge...

Here's my first iteration of the purge bucket for the Geeetech A20M. Installing this along with the tool changing script (tested on Simplify3D Only), will allow the purge to happen within the bucket instead of the printer printing a purge tower. This...

This is the Fan Duct for the Genuine Geeetech Front Fan.

Cool thing I made from 2 spare 25x37mm ball bearings. ...No supports (you might need mental to get threads to work perfectly in first try). You need nut which i believe is M30x1.5, and comes in standard GEEETECH package.

I decided to start with my A10M by implementing the following upgrades: 1) Enhancing Cooling for the GT2560 V3.0 Board 2) Improving Cooling for the printed Part 3) Adding LED-Lights to the Buildplate 4) Fixing the cable mess Geeetech created on the...

This design should work on all recent Geeetech printers with a super plate (About 5.5mm total thickness of heatbed + glass plate), including A10, A10M, A20M, A30. I tested it on my A10M. It is recommended to print in PLA and then anneal it. I put...

This is just a simple replacement for the stock fan duct. It has some advantages to the mostly (not so nice) printed stock fan duct. Much more airflow due to optimized flow channels... pointing directly on the material left and right of the nozzle,...

I didn't have TPU filament or a similar substitute available, but I did have silicone on hand. However, I wasn't confident that printing with these materials would produce high-quality results using a bowden extruder. To overcome this challenge, I...

This is a simple replacement for the stock fan duct.\r\nIt offers several benefits over the typically (not so pleasant) printed stock fan duct.\r\n\r\nSignificantly more airflow due to optimized flow channels... pointing directly at the material left...

I love the BigMac MKII setup but it haven't a mount for a BLTOUCH. ...So I created one

**0.3.03.19 UPDATE**: I've uploaded a new version tailored specifically for 2x 5015 fans, as well as a fresh 2mm longer end piece compatible with Geetech's newest nozzle. The "fanduct end 1.1" is designed to work seamlessly with the long nozzle,...

Replacement for stock extruder fan duct - Geeetech A10M 2 (dual colour). Print in orientation as shown in image #3. Supports = touching build plate only. Original bolts used. Designed in Fusion 360. ...Sliced in Cura (4.5)

A revised version of an A30T Fan Duct i found on a FaceBook group. ...to fit a Geeetech A10M fan that has the 3 mounting screws and this hinges off the lower screw.

Geeetech A20M Drehknopf für Levelschrauben

This page will be usefull to store in the same place all the parts that are from the new version of the geeetech A10M. Cura: -A10M_Printer_Gcodes470_Marlin203.txt: This is the start and end g-codes for the printer that works for me in cura 4.7.0 and...

Drawers for the Geeetech A10M are designed to fit snugly below the print bed of this versatile 3D printer. This clever design allows users to maximize their workspace while keeping essential components organized and within easy reach. Four carefully...

To access the printer's feed, I decided to install the Geeetech A10M extruders facing downwards. Mounting them as instructed would have left me struggling to get the filament into position. However, this approach led to runout sensors that were...

I saw some fan cover for Geeetech to protect the electrical boards from any falling plastic during printing, but it does not work for the new version of A10M. So I took the possible measurements to make a new fan cover that will not block the...

I'm making a fan cover for my Geeetech A10M printer, so I'll attach it with double-sided tape. I downloaded and printed the parts that were supposed to go together just like this one, but unfortunately, I couldn't install them because the space...