geeetech a10m vs a20m 3d models

The sock fits very well on the heating block of our A20M and A10M long nozzle, but it can be trimmed to fit short nozzles. The sock has a thickness of 1.8 mm on its contours, 2 mm at the bottom, and 1 mm around the nozzle to minimize heat dispersion....

The sock fits very well on the heating block of our A20M and A10M long nozzle, but it can be cut back at the nozzle to fit short nozzles. The sock has a thickness of 1.8 mm on the contour, the lower part of 2 mm and the contour of the nozzle of 1...

For the A10M & A20M I recommend this mold I've been using (https://www.thingiverse.com/thing:3569700) with Smooth-On Mold Max 60 for the silicone (https://www.smooth-on.com/products/mold-max-60/) Assembly Notes: 1) The hotend fans are mounted to each...

I copied the original A10M Fan duct and made it longer so it blow below the nozzle, also trimmed it and laid it flat by using 45 degree cuts. Print flat no supports needed. also added a short version I use for my E3D V6 hotend. ...May also match other...

To get around this issue, I replicated the original A10M fan duct, extended it to blow below the nozzle, and then trimmed and flattened it using 45-degree cuts. This design prints flat, eliminating the need for supports. I also created a shorter...

The cooling system on my A10M and A20M was not fully convincing, so I designed this part with several key concepts in mind: 1. Replace two 30mm fans for the hotend with a single more silent 40x10 or 40x20 Fan. 2. Improve cooling with a radial 5015...

Mounting instructions can be found in the PDF in the file section: <------ If you like this mount please use the "TIP DESIGNER" button and leave a tip for a hot or cold beverage. you can also use the link: https://buymeacoff.ee/redangel1984 , if...

Because the cooling on my A10M and A20M was not quite convincing, I designed this part with several key concepts in mind: To achieve more silence, I opted for a single 40x10 or 40x20 fan instead of two 30mm fans for the hotend. This change also...

This is a design to attach the NF Crazy TC-03 2in1 hotend to my Geeetech A20M printer. I made a first design that did not fully meet my expectations. Then, I created a second one (files with "flat" in the names) which has several advantages over the...

Update 29.12.2018: Version 1.1 of Skorpion where the duct mount was thickened and the duct outlet was shortened to be a little more far away from the heater block Because the cooling on my A10M and A20M was not quite convincing, I designed this part...

Replacement for the A10M filament sensor, which I needed to replace after mine broke. To create a new sensor holder, I designed a custom cradle that fits snugly around the original sensor and connects directly back to the ball socket. ... Using hot...

... visit https://www.paypal.me/akoswonerth for a PayPal payment. This mount design is also compatible with my Universal Fan duct, which supports Geeetech printers as well as other makes and models: https://www.thingiverse.com/thing:4121546

(check out the gif on the bottom of the page) If you like it, don't forget to leave a TIP for a cold or warm beverage: https://www.paypal.me/akoswonerth This is one of my upgrades after I installed the E3D Hemera Extruder/Hotend. The slightly heavier...

Inspired by CR83D's Dual Z: https://www.thingiverse.com/thing:3742027 I designed my own version from scratch for the Geeetech printers: What you'll need: 1x Stepper Motor 1x Stepper Driver 1x Motor Cable 1x T8 Lead Screw and nut (Pitch 2mm, 4 start,...

Design a basic silicone sock mold that can be printed with precision. Opt for a layer height of either 0.1mm or 0.2mm to ensure accurate dimensions. Any other settings risk compromising the mold's integrity. For seamless use without disassembling...

Who hasn't faced the challenge of adjusting the BLTouch's height after swapping nozzles? It was a game-changer for me when I discovered that the nozzle had shifted to a different height. By making these adjustments, I could fine-tune it to the...

This custom spacer brings the two spool holder brackets together, enabling them to be secured with zip ties. By doing so, the number of screws required to attach the spools to the frame decreases significantly, and positions them directly at the...

This design is a reworked version created by MackiFPV. I decided that since my printer has a two-color printing capability, it would be beneficial to adapt this feature for the extruder lift blocks. These custom blocks allow users to mount their...

Simple Silicone Sock Mold: Key Printing Parameters Revealed To achieve precise dimensions, print this mold at a layer height of either 0.1 or 0.2 millimeters. Any deviation from these settings will compromise the mold's accuracy. For a hassle-free...

This silencer cuts down the racket generated by the extruders by 3-6 decibels: https://youtu.be/AWhgYuN5S6s. This is an upgraded version of the initial model: * Eliminated the need to use M3 screws and T-nuts * Simplified the part (no supports...

I optimized this part here: https://www.thingiverse.com/thing:3367569. It's recommended to print the improved part instead. This dampener effectively decreases the noise produced by the extruders by 3-6 decibels: https://youtu.be/AWhgYuN5S6s ...

A hinge mounting style for PCB extruder.Use M2 (with washers) or M3 screws to mount.

This Holder is Easy to Attach - No Need for Bolts or Screws

Cache écran GeeeTech A20M

Standard carriage for Geeetech A20M

Cable support for Geeetech A20M

This adapter was designed specifically for pairing a Chimera or Cyclops hotend with the carriage of an A10M or A20M printer. I opted to utilize the existing screws from the stock hotend for mounting purposes, allowing for a seamless integration. At...

After trying other A10M Parts Fan ducts, and they blow on nozzle i remixed to place it lower and add lip to force some air downwards. ...Also fillet mounting hole corner.

After experimenting with alternative A10M parts fan ducts, I decided to modify one by relocating the nozzle downward and adding a lip to redirect airflow downwards. ...Additionally, I smoothed out the corner of the mounting hole for better structural...

Specially Designed for Geeetech A20M/A20 Nine-Point Test to Verify Platform Level, 255x255 Size