geeetech gt2560 rev b 3d models

Upgraded Airflow System for Geeetech GT2560 REV A+: Enhanced Performance through TMC Driver Integration

This is a straightforward solution - a basic mounting bracket designed specifically for the Geeetech GT2560 Rev. A+ motherboard. ...Two such brackets are used to securely fasten the board beneath an IKEA LACK table, cleverly repurposed as a printer...

92mm fan mount for GT2560 rev: A+. Can replace the sidemounted 40mm fan. ... Minor adjustments using pliers/cutters might be needed.

So I created this Geeetech I3 Pro B GT2560 cover with FAN and door. It accommodates a bigger 70mm, quieter fan, located on a door, so you still have access to the GT2560 board. 4 x magnets keep the door closed. Uses all existing holes in the...

Case designed specifically for the GT2560 board and accompanying cables, featuring an integrated 80mm fan. ...Constructed to complement the Geeetech i3 Pro B 3D printer.

GEEETECH GT2560 Board cover for Prusa i3 pro B, i made holes for fixing nuts with soldering gun and fix them with silicon gun, if you prefer you can make trough holes.

remixed Geeetech GT2560 housing, made with bits taken out parts to give smaller foot print and print flat on G2s

I crafted a custom cover for my trusty Prusa i3 Pro B using the Geeetech GT2560 board. To secure it firmly in place, I carefully drilled precise holes for the fixing nuts. Next, I employed my reliable soldering gun to give them a sturdy base.

I swapped out the Sanguinololu in my Prusa i3 with a Geeetech GT2560, giving it an extra set of mounting brackets that allowed for a snugger fit. ...I then printed up replacement brackets for two machines.

I'm excited to share with you a custom mounting solution for the GT-2560 Rev A+. It's designed to securely fasten the board onto a plate. ...I'd love to hear your thoughts and see if this design meets your expectations!

There are plenty very nice housings available for Arduino and RAMPS, but none for the Chinese all-in-one version GT2560. Attention: Various board sizes exist, with the default version measuring 110mm x 79.8mm x 36.8mm in dimension. A "universal"...

Print Settings: Printer: Geeetech Pro IX Supports: Yes Infill: 15% Notes: I printed the top enclosure in ABS Chroma green with 240C and 105C using Repetier at 0.2 layer thickness. I strongly recommend using an SD card as it takes quite a while to...

... design aesthetic. Furthermore, I have developed a bracket that can be attached directly to the GT2560 housing unit. For those looking to build a case for their Raspberry Pi B+, you'll need to download and install the "raspberry_cover_b+" file.

Easy Mounting Kit Now Available for Popular GT2560 Motherboard

... and updated parts. ...If you've removed the PSU and mainboard from your printer, this could be the solution to all the mess. Print Settings Printer Brand: RepRap Printer: Geeetech Pro B Rafts: None Supports: None Resolution: 0.2mm Infill: 20%

This is a remix of the GT2560 housing from lukie80's original design on Thingiverse, specifically thing:1279978. I have also incorporated a mount for 2020 extrusions into this remix. Additionally, I made the USB outlet slightly larger to match some...

This remix is based on the 81mm version designed specifically for the A+ version of the GT2560. However, it should also fit other versions without any issues. ... The frame itself requires no supports at all, but the lid needs some support from the...

This is a GT2560 rev A+ board designed to be installed in place of the Melzi board on the CR-10. There are small tubes for passing cables under the board. The ring on the side is intended to accommodate a 10Kohm potentiometer for those who have...

Links: * https://www.reddit.com/r/3Dprinting/comments/7l0c3x/gt2560_and_tmc2130/ * https://www.geeetech.com/forum/viewtopic.php?t=60658 * https://discuss.toms3d.org/hardware-f6/issues-with-tmc21030-on-the-gt2560-t427.html # Misc GT2560 V3 Links *...

A custom-made cover mount for the Geeetech GT2560 controller board, specifically designed to accommodate a 70mm fan. The cover comes with a built-in standoff to secure the back side of the board. I used M3 threaded rods, which are essentially M3...

This plate attaches directly to the Geeetech GT2560 using 30mm spacers.\nYou can mount a 60mm fan on the plate to cool the drivers and other components on the board.\nUsing TMC drivers and a quiet 60mm fan transforms your printer into a stealthy...

Straightforward enclosure / 80mm fan mount designed specifically for a Geeetech GT2560 control panel. The design incorporates a standoff on the back side of the board. ...For added security, M3 threaded rods (M3 screws with trimmed heads) can be glued...

Bracket was printed for replacement of the "original" GT2560 board fan, provided with the printer. Original fan was loud and annoying during print, so I decided to replace it with bigger and much quieter fan. I've used standard 80mm computer fan and...

Remixing the Geetech GT2560 enclosure for a snugger fit, measuring in at under 150mm, allows for effortless printing on the Printrbot Simple Metal. ...Strategically placed honeycomb ventilation holes within the box and lid facilitate optimal cooling of...

I replaced the loud GT2560 board fan that came with my printer with a new one, Bracket, to make printing more enjoyable. The original fan was extremely annoying during long print sessions, so I opted for a larger and much quieter fan instead. A...

My Take on Lukie80's Design for My Geeetech Prusa I3X Redesign on the 3030 Profile. ... I've also Got a Fresh Twist on the Prusa I3 Mk3 PSU Holder Redesign at https://www.thingiverse.com/thing:3192996

Both are made for Geeetech GT2560 Rev a+ (possible fit others as well?) Rev 2 is made for Raspberr Pi Zero, also with space for an DC-DC converter. Attached is also a cover with cutouts for 2 x 40mm fans Rev 3 is made for Raspberr Pi 2/3/3B. Attached...

Both are designed to work with Geeetech GT2560 Rev A+ (and may fit other models as well). Version 2 is created for Raspberry Pi Zero, also featuring space for a DC-DC converter. Attached is a cover with cutouts for two 40mm fans. Version 3 is made...

Both are made for Geeetech GT2560 Rev a+ (possible fit others as well?) Rev 2 is made for Raspberr Pi Zero, also with space for an DC-DC converter. Attached is also a cover with cutouts for 2 x 40mm fans Rev 3 is made for Raspberr Pi 2/3/3B. Attached...