glass clips 3d models

I have a Monoprice Select Mini V2 and used these clips to fix the glass into the heated bed. You can cut them in half if you like to make 4 for the corners. ... I printed several sizes until I fount the perfect one.

Glass clips for the Printr bed and 1.5 mm glass. ... Instructions Print 4 Use the outer holes to clamp the glass and bed in place

glass clips for the FT-5 printer This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/0LrqYZuqpvj

4mm glass clips for CTC Bizer. To use with 150x230mm deskt. You can use the corners only ore use the sides only. If you want to fix it strong use all. it could be helpful to change some values in printer script before the print start. When...

Glass clips for a Printrbot PLUS v2 with 1/8" 8" square glass Instructions These were designed to work with a Printrbot PLUS v2 and McMaster-Carr Borosilicate glass (#8476K18)... but will likely work with any printrbot with heated bed and 1/8" thick...

i got tired of after a couple prints the clips would get loose due to heat and allow the glass bed to move around every clip i tryed had that issue so i put all of my knowledge and diffrent styles from various makers together to get these they fit my...

I modify the inital glass clip by bitrunner to make this usefull on the printrbot metal plus :-)

I modify the inital glass clip by bitrunner to make this usefull on the printrbot metal plus :-)

This glass table clips are only useful for people who have auto bed leveling. ( http://www.thingiverse.com/thing:612643 ) This was made to be use on BQ Prusa I3. ...Print Settings Printer Brand: RepRap ...

Instructions Easily adjustable glass clips for the Printrbot Plus. I made these glass clips for my Printrbot Plus. They might also work on other models too. It would probably be better to remove the wood to install these but I was able to do it with...

This glass table clips are only useful for people who have auto bed leveling. ( http://www.thingiverse.com/thing:612643 ) This was made to be use on BQ Prusa I3. Print instructionsCategory: 3D Printer Accessories Summary This glass table clips are...

The reason is that this design doesn't allow the clips to spin, which with previous glass clips on Thingiverse could allow the bed to get free mid-print. These are designed to hug the stock clips tightly, so they become a second point of contact and...

Clips made specifically for printrbot holes and 1/8" glass.

Wheel holding clip for a shower cabin glass doors

Instructions Print off 4 clips, these were designed to work with the heat bed on a Printrbot+ with an 8" square 1/8 sheet of borosilicate glass from McMaster-Carr. The print had some problems so the clip needed a lot of fine-tuning. ...After I get my...

... should make. ...These clips strap down the glass on the build platform. The glass I used was 190x190 mm. I also screwe the 4 corner bolts down tight to squish the spring solid because I didn't like the spring loaded platform. ... www.MakerFront.com

Unfortunately it's tricky to hold glass larger than the print bed in place, because you have to use large binder clips, and the extruder can run into the clips. And you can only clip down two edges, because the other two edges stick way out. So I've...

And it has thin edges, which allows using small binder clips. Warning: Glass can Break One caveat - $1.99 plate glass is 3/32" thick, so it's not as durable as thicker, more expensive glass. But in my experience, as long as the glass is flat on...

So I had a idea of using clips to connect to the glass. I did not see anything similar on thingiverse. So I decided to make my first make. The center middle piece (led center bar v4.stl) I did use double side 3m tape to attach. If it does give...

I finally ran out of Robo3D's bed adhesion tape so I ordered a piece of Borosilicate glass from Amazon and designed these clips to hold the glass in place. Works great and holds it well. The one I order is listed below. It has a 130x130x3 mm...

I installed a 4mm glass bed, but it was measured the exact same measurements as the Wanhao Build Tak, so non of the other clips sorted my issue, and i could not easily get silicon adhesive pads in South Africa easily. You really only need two clips,...

This is a newly made glass clip to hold 8" by 8" regular window glass you can buy at the hardware store to the bed of a Printrbot +. For some reason the clip this is descended from didn't clip it tightly enough. This is made from scratch but I got...

Glass clip for Velleman K8200 Use 8 of this clip to mount a 215 x 215 x 4 mm glass sheet for excellent prints. ...This clip has a easy release hatch

Creality Ender 3 Glass Clips (5.7mm + Stop) Good for Bed + Glass 3mm. ... Perfect blocking.

Bed leveling thumb wheels and glass clips I use on my CTC Prusa I3 Pro B

Bed leveling thumb wheels and glass clips I use on my CTC Prusa I3 Pro B Category: 3D Printer Parts

Glass clips made to fit my Duplicator i3 Plus printer with an aftermarket 3mm glass bed. ... Print four clips, they should snap in snugly with the pointed radius around the spring.

... plate! Inspiration for: Corner Glass Clip by Harlique:http://www.thingiverse.com/thing:537595 Wing Nut cover by legreatmagnet:http://www.thingiverse.com/thing:604579 Instructions I modeled the corner clip in Autodesk's TinkerCAD application (Free).

We printed the FlashForge Creator Pro - Corner Glass clips, and they work great. Unfortunately, our glass build plates aren't quite uniform in size, and some were too small for the original corner clips to get a good grip on the glass. ...We extended...

Shortened jherridge's glass clip design by 2mm, so it doesn't stick up above my glass plate. Was having problems with the extruders hitting since the glass I am using is thinner than what the clips were originally designed for. ...Print Settings...