glass patio table top clips 3d models

These are the clips that slide into the inside edges of the C-channel rim of a glass top patio table & support the glass. The pieces with the "H" pattern on the back are for the sides & the "Leg End" pieces should slide over the end of the top of...

These are the clips that slide into the inside edges of the C-channel rim of a glass top patio table & support the glass. The pieces with the "H" pattern on the back are for the sides & the "Leg End" pieces should slide over the end of the top of...

Clip for 1980's glass top round patio table

Replacement clip for glass patio table. ...Designed as replacement parts for a friend's patio table.

A duplicate spacer/clip for the ones under my patio table that were dissolving due to age. The clips go into a metal band and act as a spacer holding the glass against the upper lip of the band. ...It was designed to be printed without support.

I noticed that the plastic supports holding the glass surface of my patio table have been breaking and falling off. I took one of the broken ones, made some measurements with some guesses as to the screw hole size and center location, and printed one...

I decided to re-paint my ~20 year old aluminum glass-topped patio table. When I was removing the glass, the plastic (or maybe some sort of resin) supports holding the glass table top in from the bottom were all yellowed and most disintegrated or...

I noticed that the plastic supports holding the glass surface of my patio table have been breaking and falling off. I took one of the broken ones, made some measurements with some guesses as to the screw hole size and center location, and printed...

This is a connnector for a glass topped patio table with rounded rectangle hollow metal legs. Made these as I needed a replacement for a diy refurbishment on my patio table and couldn't find spares to buy online. I'd recommend printing in PETG or...

It was made to replace a grommet in my table that had locking tabs that have since broken off. There were not replacements found for it, so I made a better one myself. Top and bottom screw together quick snugly. Print Settings Printer Brand: ...

One of the two design here was based on the inital openSCAD file from Glass Patio Table Rim Clip by Ettie . So I had this patio table that started to be fragile and shake. The way it is designed structural parts depends on those plastic elements to...

Replacement grommet for the umbrella hole of a glass outdoor table. *** Must be printed in a flexible filament. Print shown was printed in TPU. *** Glass thickness: 5 mm Glass hole diameter: 50.4 mm Grommet Umbrella hole diameter: 40 mm Grommet...

Glass Top Side Table

A replacement part for broken clips that hold the legs to the top of my small glass patio table.

A concept design for table with a glass top

Glass Top Dining table with cast iron hardware, rustic 8x8 legs.

We inherited a glass top table, but some of the rubber pads for the glass had been lost. I modeled this in tinker-cad and printed in TPU. Its a very quick print. ...At some point I may reprint these in a darker color to blend with the wood of the table.

Table

A table that has the world made of frosted glass on the tabletop. ...Please press "Like" if you like the table.

Model of a realitvely modern designed coffe table. Constructed of metal and glass. ...Originally created as a practice model

Needed a new insert for my glass patio table to fit my new, 32mm diameter umbrella pole.  I resized the model that I found on thingiverse so that it would fit both the 32mm pole and the 50mm hole in my glass table top.  The threads...

solidworks 2016 & keyshot 5A concept design for table with a glass topAfter finishing this model I will upload the 3D-model, like I do it for my other models such as:BedroomBedroom projectstaircase

for glass table corners, made for 5.7mm thick glass. Made with rounded edges. its for my parents, they have wood table so i used wood pla, I'ive noticed a lot less stringing with wood pla printing at .1mm layer height has less stringing and better...

To increase the height of the table top, I create two holder, square and round. ...80mm height 40mm base Ø9mm hole

Just a simple table

PATIO TABLE

Chrome Metal Frame with Carbon Fiber elements. ... Swing open top with notched closed element. ... About 3" x 4" x 2"

Patio glass rectangular table - corner spare part to be made with 3D printer. ...(STL file included)

Scan of patio table using Scann3D. ...This is a failed scan that is very messed up.

Patio table Something to use some of the bits laying around the garage, might get around to it one day.