gopro gimbal mount 3d models
359595 3d models found related to gopro gimbal mount.thingiverse
Remix of GoPro Session mount for gimbal with alexmos controller Made this a bit wider (taller?) to accommodate Chinese camera with different button/screen configuration.
thingiverse
I created a first version of a GoPro mount for a smartphone gimbal. There will be some other versions with a standard GoPro mount. ... The GoPro I use is the Kitvision 4KW, but you can use any GoPro with 59.30 x 41.15 x 29.30mm.
thingiverse
This is a mount I designed to be used with the FeiYutech WG2 wearable 3 axis gimbal and it attached to a baseplate that came with the Explorer Action Camera (not a GoPro; similar but much cheaper). I used 1/4-20 x 1/2 inch machine screws to secure...
cults3d
###This is a GoPro Session Gimbal Mount for a DYS Gimbal. The GoPro is secured by clamping down the frame with two M3 screws. A nut is not needed, the screws can be screwed into the plastic. The mount gets secured with a grub screw and holds onto the...
thingiverse
###This is a GoPro Session Gimbal Mount for a DYS Gimbal. The GoPro is secured by clamping down the frame with two M3 screws. A nut is not needed, the screws can be screwed into the plastic. The mount gets secured with a grub screw and holds onto...
thingiverse
Remix of GoPro Session mount for gimbal with alexmos controller Made this a bit wider (taller) to accommodate Chinese camera with different button/screen configuration. ... Second version made walls a bit thicker for better printing.
thingiverse
I wanted to be able to use it to carry the Tarot T-2D Gimbal I already had, so I designed this mount. It needed to be easily printable, lightweight, and had to incorporate landing skids into the design. I also wanted to keep the batteries below...
thingiverse
Bügel zum Befestigen der Gopro Hero 5 an dem Z1 Gimbal Ohne Schrauben!
thingiverse
Gopro Hero 5 mount made for gimbals and stabilisers. Purpose built for the Rigiet Stabiliser (can be used without counterweight) and should fit any stabiliser that can hold mobile phones. The cut out channel on the mount allows for GoPro to slide in...
thingiverse
... for the Inkee Falcon and Gopro Hero 9/10 combo. ... Needs to be printed in TPU and it's purpose is to work as a shock mount - When using the integrated microphones your video will have the tapping sounds the gimbal makes, this eliminates those noises.
thingiverse
Yet another Gopro mount for a Gimbal, this one is designed to be bolted to a motor with holes at 12mm distance. ... It also needs brass inserts, you can get them from ebay: ...
thingiverse
FPV 3 Axis CNC Metal Brushless Gimbal With Controller For DJI Phantom GoPro 3 4 180g for RC Drone FPV Racing And the webpage below. https://www.banggood.com/search/fpv-3-axis-cnc-metal-brushless-gimbal-with-controller-for.html See the photo for the...
thingiverse
El dron en el que se ha montado es el bayangtoys x 21 este: http://bit.ly/2wrTdnF (dron barato con gps ) y el gimbal que le he instalado es este: http://bit.ly/2llR63I (modelo ideafly 2) Si estas interesado en saber como conectar el gimbal al dron,...
thingiverse
The controller used is this one: http://www.banggood.com/BGC-3_1-2-Axis-Brushless-Gimbal-MOS-Controller-with-Mini-GY6050-Sensor-p-957358.html The two motors used are these:...
pinshape
The controller used is this one: http://www.banggood.com/BGC-3_1-2-Axis-Brushless-Gimbal-MOS-Controller-with-Mini-GY6050-Sensor-p-957358.html The two motors used are these:...
prusaprinters
http://www.thingiverse.com/thing:479222 for the arms and motor covers. The controller used is this one: http://www.banggood.com/BGC-3_1-2-Axis-Brushless-Gimbal-MOS-Controller-with-Mini-GY6050-Sensor-p-957358.html The two motors used are these:...
thingiverse
It is a clip on mount that replaces the camera mount that comes with the gimbal. You just press it on and it clips to the gimbal holding the Gopro securely in place. It has tabs that allow easy removal too. ... This allows you to install and remove...
thingiverse
I designed this GoPro Mount for my Zhiyun Smooth Q3 Gimbal, because the original mount that came with the gimbal wasnt that well designed and quite heavy, meaning combined with the GoPro its weight was almost 200g, which is the maximum this gimbal...
thingiverse
No screws, no metalic bearings. ...Only two parts and a nice fit.
thingiverse
This is based on the Karma ring but with some important changes: * Flipped the nut mount point - makes access much better when wearing chest plate * Thicker mounts. * 2 Extra grip pads. * Longer mounting arm. * Vertical support ring. ... * Cutout to...
prusaprinters
This is based on the Karma ring but with some important changes: Flipped the nut mount point - makes access much better when wearing chest plate Thicker mounts. 2 Extra grip pads. Longer mounting arm. Vertical support ring. Cutout to access front...
thingiverse
Las bolas de goma se pueden comprar aquí: https://www.ebay.com/itm/4pcs-Anti-Vibration-Rubber-Damper-Damping-Ball-for-Gimbal-Gopro-DJI-Camera/122605437429...
thingiverse
GoPro Hero Session 4 mount for turbis Open Brushless Gimbal: https://www.thingiverse.com/thing:110731 no Support needed, Res 0,2mm
thingiverse
This GoPro Hero3 mount replaces the Bumblebee quadropcopter gimbal baseplate. To be printed with 100% fill, 3 shells, 0,1mm filament layer height, with raft and supports. ... http://neidhartonline.com/bumblebee/ ...
thingiverse
To serve as a tilt gimbal and anti vibration mount. To finish it you will need a 9G Micro Servo and a 4x7x2.5 bearing, the screws that come with the Servo are what fix it all together. Then to connect the top plate to the main hanger you will need...
myminifactory
This is a cool part that allows you to attach your GoPro to a gimbal, like this DIY one that I made. ... Settings: Material: ABS layer: 200 microns Extruder: 230C/ Bed 100C Infill: 20% Supports: YES Rafts: NO
thingiverse
This is my first try of a Gimbal Mount for a Spidex V2 Quadrocopter. ... Copter : http://quaternium.es/product.php?id_product=7&id_lang=1 Gimbal : http://www.thingiverse.com/thing:101698