gopro roll bar mount 3d models
444636 3d models found related to gopro roll bar mount.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_id = 3.8 gopro_rod_nut_th = 3.6 gopro_bar_th = 3.2 gopro_rod_nut_od = 8.05 gopro_bar_screw_d = 5.4 gopro_ext_len = 20.7...
thingiverse
This one is bigger so it can fit around larger bars such as a race car roll cage steel bar which was the reason behind this. Cant handle bars much bigger or smaller as it was designed to fit with maximum grip around a specific bar. I scrapped...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_d = 3 gopro_captive_rod_angle = 45 gopro_rod_nut_th = 3.6 gopro_captive_protruding_h = 0.5 gopro_ext_th = 4 gopro_ext_len = 50...
thingiverse
Sometimes the best in-car GoPro location is on the diagonal bar off the B-pillar hoop. This simple OpenSCAD design is for a 1.75" bar diameter at 45-degrees from the horizontal. Printed horizontally on a MakerBot 2 with seven shells, 50% infill,...
thingiverse
Here's the new Car Roll Bar Gopro Mount. The Diameter is 45mm, the standard for many roll bars. Customized version of http://www.thingiverse.com/thing:62800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=62800...
thingiverse
... for a 1.75in bar. ...I use this to mount my GoPro to the roll bar in my Miata. This is sized to take standard metric nuts rather than the slightly larger gopro nuts. ...Narrow enough to fit in the center of a Hard Dog Hard Core double diagonal roll bar
cults3d
gopro action camera bracket for 40 mm diameter roll bar print the parts, put them together with 4 mm metric screws, wing nut and washers. ... 40 mm roll bar gopro support
thingiverse
I wanted a better/stronger mount for my radios on my x3 roll cage, had designed some that screw together, figured this would be much stronger and easier to install. Includes the top (go pro mount) and bottom(to protect roll cage) with slide through...
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
Designed to clamp around 44.4mm ROPT510 tubing, sized up slightly to allow a wrap of electrical tape to prevent it from slipping and protect the powder coat on my roll bar.
thingiverse
Customized version of http://www.thingiverse.com/thing:62800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
This is an alternative to GoPro's roll bar mount, which has huge posts sticking out the back and does not have the necessary degrees of freedom to get the camera level on an angled bar, such as the A-pillar. This addresses both of those issues by...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_secondary_rotated = 0 gopro_captive_protruding_h = 0.5 gopro_rod_nut_od = 8.05 gopro_bar_screw_nut_d = 6.01 gopro_bar_screw_head_d = 6.2...
grabcad
This is a GoPro mount for a 43 mm tube, so it fits on most roll bars. ...Changing the diameter shouldn't be too hard just cut extrude a larger hole.
thingiverse
A Gopro mount that fits on a 41mm diameter roll cage tube (Porsche 996 GT3 mk1 Clubsport)
thingiverse
This fits around a 38mm or 1.5in roll cage or roll bar tube and holds a standard GoPro mount. ...It is designed .25mm small to allow for clamping force and has space for M4 hardware to fasten it.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_primary = triple gopro_captive_rod_angle = 45 gopro_ext_th = 5 gopro_bar_screw_head_d = 13 gopro_secondary_what = clamp gopro_rod_nut_od =...
thingiverse
This is a bolt on mount for a Honda Pioneer roll bar. ... I intend to use four of these to attach a piece of plastic as a ridged roof replacement.
thingiverse
My GoPro camera was stolen more than a year ago and with it the roll bar mount. I finally got a new Hero 3 without mount this spring. So a roll bar mount was all that was missing. Here's my simple but rugged version of such a mount for tubes between...
thingiverse
... RZR 900. ... Printed in PLA at standard settings. Supports are needed as the clamp is printed on its side to avoid stress in the layers when clamped around the roll bar of the RZR. ... Works with Go-Pro and Go-Pro clones, and their accessories.
thingiverse
GoPro Handlebar Mount - Uses 2 off M5 caphead screws to mount to the handle bars. ... Designed for 31.8 mm bars.
thingiverse
Used ProDesktop to create this Gopro clamp for the Greenpower Kitcar. It should fit nicely on the right side of the rollbar above the drivers head. Room for the back of the case to open in situ even if you have a extra battery pack attached.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_th = 3.2 gopro_primary = triple gopro_bar_screw_nut_d = 6.01 gopro_captive_rod_id = 3.8 gopro_rod_nut_th = 3.6 gopro_ext_len = 35...
myminifactory
The 3D printed Bike Bar Mount has been designed to be 100% 3d printed with no additional hardware needed, just the GoPro. the mount is made to fit a 30mm Bar, but I have included two adaptor rings one so it will fit a 25mm bar and also one for a 20mm...
cults3d
The 3D printed Bike Bar Mount has been designed to be 100% 3d printed with no additional hardware needed, just the GoPro. the mount is made to fit a 30mm Bar, but I have included two adaptor rings one so it will fit a 25mm bar and also one for a 20mm...
thingiverse
This is a GoPro bar mount for the clip. You can also print the upper part separated and mount it with a M5 screw. Based on https://www.thingiverse.com/thing:2082169 and https://www.thingiverse.com/thing:3472928 This thing was made with...