ribbon cable holder 3d models
408604 3d models found related to ribbon cable holder.myminifactory
Ribbon Cable Holder 2040 e.g. ...Pi Camera Cable clips on to 2040 section
myminifactory
This is a ribbon cable holder for 3030 extrusion of the Prusa i3 MK3. Print 3 or more holders. ...I would recommend to print using PETG or ABS.
prusaprinters
Just Ribbon Cable Holder 2040 e.g. Pi Camera cable holder Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.16 Infill: 25% Filament: Polymaker Polyflex TPU Black Notes: I used Polyflex TPU, with...
prusaprinters
Remix of the MK3s display ribbon cable holder, this is an individual LCD Ribbon Cable Holder.Updated 25 March 2021 with repaired .stl files at both 7.8mm and 7.55mm heights.Print instructionsIndividual ribbon cable holder for the MK3S. ...Print 3 or 4...
thingiverse
Simple Ribbon Cable guide / holder for Sovol SV03 printers maybe others. I didn't like how my cable drooped and bent. Holes to screw it down or can use double sided tape. Print long side down to use less support. ... PLA, 20-25% printed down on long...
thingiverse
After trying different designs to guide my 3d printers ribbon cables, I finally ended up with this design. Each clip can easily be mounted with a small screw (I used a diameter of 3.5mm). I made clips of two different widths. One for ten poles...
thingiverse
A Multi-Ribbon cable holder for a 30x30mm profile.
thingiverse
Well, standard Extruder is not really running smoothly without a special fan duct as well as a ribbon cable holder. I designed a new riboon cable holder. ...Fanduct as well as vent clip from Humebeam.
thingiverse
This ribbon cable holder screws to the rear of the right Z axis carriage (where the previous models attached the drag chain to) to free up the top of the crossbeam. This was designed to go with my Crossbeam flip brackets: ...
thingiverse
This is an automatic ribbon cable holder for QIDI X-Max, it retracts the cable automatically, meaning there is always tension on it (when needed) so the cable doesn't dip down causing stress on both the ribbon cable and its connector (both are known...
prusaprinters
Update Dec 1, 2021I've added step files for easy editing in case you want to make it fit your specific printer, Qidi tend to change their printers without notice from time to time.DescriptionThis is an automatic ribbon cable holder for QIDI X-Max, it...
thingiverse
Cable holders for aligning the ribbon cable for the CR10 Max. One end attaches to the lower V slot in the base profile and the other one is secured with an M4 bolt and a T-nut. ...For best results captive M4 slot nuts are recommended.
thingiverse
A cable holder for the Cetus 3D printer that attaches to the 2020 extruded section serving as the Z-axis. Holds the ribbon cable for the extruder in place. designed in SolidWorks. To install, insert the clampy bit vertically in the 2020 extrusion...
thingiverse
I designed this to hold down the large ribbon cable being used with the SD card Extension on my Ender 3. ...Fits 2020 extrusions.
thingiverse
just a frame clip for 3030 extrusion to hold ribbon cables there are 2 versions , one doesn't clip on top to allow the bed bearing to slide by on mk3
thingiverse
This thing is designed for 15mm wide ribbon cable, like the display cables for the Anet A8 LCD. Use 8mm wood screws to fix the guide to your case and move the cable behind it. It should be springy enough, that you don't have to unmount it to remove...
thingiverse
This is a little holder for a micro sd card extension. Helps just get it up off the table or wherever you have it lying. The following link is the extension I used and is a very snug fit. ...
cults3d
Simple snap in ribbon cable holder for the Anycubic i3 Mega (S).
thingiverse
Simple snap in ribbon cable holder for the Anycubic i3 Mega (S).
thingiverse
Just a mod of the Ribbon cable to hold the filament feed tube inline with the ribbon cable. ...I redesigned this in Inventor so that it can be adjusted later.
thingiverse
I didn't want to stuff the ribbon cables on my Prusa MK3S into the extrusions, so I made this twist-in clip to hold the ribbon cables next to the aluminum extrusions.
thingiverse
Angled ribbon holder for CR10S PRO, designed with Fusion360. This holder keep the ribbon above the printer stand. Needs just to tapping the hole of interface_a for lock interface_b with en fastener, but other solutions are possible ! ...The ribbon...
thingiverse
A Clip that gives the extruder ribbon cable extra support , Dose not pinch cable and lets it have some movement to reduce stress on wires and Does not interfere with normal printing. ...Slides on just like original clip
prusaprinters
Cable holders for aligning the ribbon cable for the CR10 Max. One end attaches to the lower V slot in the base profile and the other one is secured with an M4 bolt and a T-nut. ...For best results captive M4 slot nuts are recommended.</p> <h3>Print...
thingiverse
This is a bracket that keeps the bed's ribbon cable away from the print area, and additionally can help keep the cable from peeling off of the heating pad. It is meant to be detachable, however there is a screw hole for permanent placement on the bed...
prusaprinters
This is a tiny clip to hold the flat ribbon cable from a Raspberry Pi Camera in place. ...Use a 2.5 mm (x 10 mm) screw to mount.</p> <h3>Print instructions</h3><p>Printer Brand: Prusa<br/> Printer: Mini<br/> Resolution: 0.2mm Speed<br/> Infill: 20%<br/>...
grabcad
This is a Ribbon cable holder specifically for V slot and it is twist in type cable holder does not require any nut bolts or screws.