gopro webcam stand 3d models
182650 3d models found related to gopro webcam stand.thingiverse
This is a simple stand to mount a Gopro or webcam. ... It uses a 1/2 inch square dowel which can be cut to whatever length you desire.
thingiverse
My Logitech B910 webcam has a broken stand and I decided to model a glue-on gopro style replacement. This is a permanent replacement of a broken and missing monitor mount stand. I used CA glue after roughing up the smooth plastic on the back of the...
thingiverse
Table stand for monitor-mounted webcam. ...You can glue rubber pads underneath or just pour liquid silicone inside cavities.
thingiverse
It's a very simple stand for a webcam. Without mount, but you could simply drill a hole. ... I'd recommend laying it down.
thingiverse
This is table stand for monitor-mounted webcams. ...You can glue rubber pads underneath or just pour liquid silicone in cavities.
thingiverse
Needed a webcam stand for this old cheap webcam. The ball is 10mm and the shaft is 5mm. Got tired of dealing with the lousy stand that shipped with it and built this up in sketchup. Worked great on the first try. ...
thingiverse
A simple webcam stand for any camera with a standard 1/4 20 thread on the bottom. Print with 15 to 25% infill. No supports required. Use with this screw. ... https://www.thingiverse.com/thing:578514
thingiverse
a simple webcam stand with 2 parts (CAGE, STAND) which i created for my Ultimaker3 (maybe works with other models too? plz let me know!). The built in Webcam is nice, but i wanted an additional one on the top for streams. So this one is put on the...
prusaprinters
A simple webcam stand for any camera with a standard 1/4 20 thread on the bottom.Print with 15 to 25% infill.No supports required.Use with this screw.https://www.thingiverse.com/thing:578514
thingiverse
I created this webcam stand out of necessity. It is designed so you can print as many arms as you want to change the height. The end cap is threaded to with a 1/4 - 20 thread, which is the standard size for cameras, video cameras, webcams, etc. It is...
prusaprinters
a simple webcam stand with 2 parts (CAGE, STAND) which i created for my Ultimaker3 (maybe works with other models too? plz let me know!). The built in Webcam is nice, but i wanted an additional one on the top for streams. So this one is put on the...
thingiverse
So I built a stand out of a couple of hunks of 2x4, and that was OK but was pretty clunky, so I built this, and it's much smaller and cooler. It prints flat, so it's quite strong, and press-fits tightly. Full disclosure: I cleaned up the...
thingiverse
matias_baezさんのWebCam Holderに組み合わせて使えるスタンド部分です。 WebCam Holderを差し込む際に少しヤスリで削る必要があるかもしれません。 M3x15のネジを使用します。 このカメラの中身を使いました。 http://amzn.to/2n4e5y0
prusaprinters
I designed this to be used with a logitech brio but it should work with any webcam that has a ¼-20 thread. ... </p><p>Hardware Required:</p><ul><li>1x M4 x 30mm</li><li>1x M4 Nut</li><li>1x ¼-20 x .750 SHCS</li></ul><p> </p>
thingiverse
... Also, this holder is a device that allows you to illuminate your image from a distance when using your webcam. The joints are still being studied and experiments are ongoing. Hope a lot of attention. ... https://youtu.be/X7QBWNBF0kw
cults3d
... VESA standard. Also, this holder is a device that allows you to illuminate your image from a distance when using your webcam. The joints are still being studied and experiments are ongoing. Hope a lot of attention. ... https://youtu.be/X7QBWNBF0kw
thingiverse
I wanted a webcam arm that was taller than the ones I could find. There are three lengths of thumb screws. The long one is for the base link, the medium for all of the other arm links and the "tightening" version for holding the camera to the mount.
thingiverse
Here´s a adapter for a webcam C270 for GoPro mounts. ...With an example for what I used it.
cults3d
I needed a mount for a webcam, and decided to use GoPro-style arms; GoPro-style fixtures melded with 2020 channel mounts; and a triple-arm webcam mount - also with GoPro-style fixtures - to tie it all together. To some extent, I "bounced" off the...
thingiverse
I needed a mount for a webcam, and decided to use GoPro-style arms; GoPro-style fixtures melded with 2020 channel mounts; and a triple-arm webcam mount - also with GoPro-style fixtures - to tie it all together. To some extent, I "bounced" off the...
thingiverse
This is an mount for a Kano webcam to attach to any gopro mount. ... I assembled this from other projects to use with the gopro version of camera mount: https://www.thingiverse.com/thing:3401768 I find some electrical tape wound around the front/sides...
thingiverse
Desighned to hold my Gopro over my monitor as a webcam using a usb hdmi capture card, recomend printing it with tree supports on cura with a low infill of like 20, i used 0.2 layer height but anything would probably work.
thingiverse
The exact model is Chicony HD205 94V-8 To adapt the laptop webcam to use it as external webcam / octoprint cam you only need to cut the original cable and solder it to a USB cable. The cut in the back of the cover is intended for the original flat...
thingiverse
I couldn't find another project that was meant for this, so I decided to create this myself. ...This webcam mount works with my ASUS PB287Q 4k UHD LED Monitor.