gps puck 3d models
10237 3d models found related to gps puck.cults3d
This is just the holder for the GPS puck, not the stand! ...It was inspired by Seattle's Space needle.
thingiverse
This is a GPS puck mount for a DJI N3 GPS puck. I used it to mount the puck on my small quadcopter. The puck fits perfectly into the mount with a small amount of play. ... The mount was attached to the frame with 3M outdoor double sided foam tape.
thingiverse
Looking for an aerodynamic solution for the GPS puck that will protect it in a crash? Here you are, the Frame Mount. It is locked to the frame with two screws (that also hold your arm on). The holes are countersunk so no vibrations are...
thingiverse
TPU Mount for the TBS GPS Puck on the rear of the top plate. Use a ziptie to hold down the front of the mount. ...30 degree mount
thingiverse
Designed to hold a GPS puck in an E-Flight Opterra. Includes a number of holes to accommodate the exit angle of different pucks. Puck can be secured to this using double-sided tape and then this item to your Opterra using your favourite means of...
thingiverse
Provides a solid, and VERY light mount for your GPS puck. IMPORTANT After installing this mount, look up your declination here: http://magnetic-declination.com/. I mark my puck with a magic marker so I don’t forget. Use a simple protractor to set...
thingiverse
This thing has been designed to allow the stripping down of an M8N GPS puck and mount the internals on a flight controller stack. I tried the BN-800 GPS module, which was extremely slow, especially on cold start. I found out that the BN-800 is an...
thingiverse
I LOVE my Skylark OSDs, but it’s really difficult to find a good way to mount the (expensive) GPS module. This little mount attaches to your multicopter’s arm with two zip ties & allows you to remote the antenna anywhere within cable length – even...
thingiverse
... the white plastic piece further forward. ...With my printer/material the GPS puck snaps into place fairly securely, but I used some 3M VHB between the puck & the mount anyway. ... 15/07/2018 - updated with thicker base (point of failure in a crash)
thingiverse
Hey Guys I designed an GPS Mount for the Matek M8Q to be mounted on the MB Epic Seat. If you need modifications for your gps modules, leave a comment. ... Have Fun with it :)
thingiverse
Mb epic gps puck holder
thingiverse
It's larger (a tiny bit) so it's easier to fit all the cable, the GPS is lifted up a bit for same reason and most importantly, it's a lot sturdier so it's harder to break when closing/opening the puck. On a precise printer with good ABS (recommended...
thingiverse
I had trouble slicing the files from Sceeker so I remodelled it and as the pins were prone to breaking I made a sturdier way to connect top and bottom - it's a nice snug fit in ABS on my printer. ...Print Settings Printer: ...
thingiverse
I mixed http://www.thingiverse.com/thing:1174067 and http://www.thingiverse.com/thing:1235271 so i could use this on my CX-20 with UBLOX M8N Print Settings Printer: Wanhao Duplicator i3 ...
thingiverse
This is a simple Naza GPS Puck for the Sky Hero Spy arm. ... Instructions Print in ABS with a Layer Height of 0.2 Use double side tape to hold in position on the arm side and gps side
myminifactory
I needed to mount a puck style GPS/compass on a Reptile Dragon 2, so I drew up this piece that screws into the stock location in place of the cover, and gives a nice round pedestal to stick the GPS/compass down with mounting tape. There's a channel...
thingiverse
This is a GPS holder for Here GPS on a MytwinDream hatch. ...GPS puck should be flush with the hatch.
thingiverse
All it takes is for the GPS to fall off once during flight to get the creative juices flowing. ... This design assumes you still have the double stick backing on the GPS puck.
thingiverse
This was designed to both hold the BN-220 gps puck and tidy up all the wiring going into the flight controller.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Instructions Using the following options: font_catch_diacritical_sign = 2.3 textheight = 2 do_shift_font = automatic base_radius_add_percent = .1 baseheight_percent = .33 RoundedBase = 0...
thingiverse
This is PUCK. I Kickstarted him and his buddies last year with the intention of doing a resin and vinyl run. Life and a baby has meant that little project is on hold now but as I think he is too cool to be locked away i'm putting the original st. I...
cults3d
Artist: Harriet Hosmer Period: 1856 Material: Marble Location: Walker Art Gallery Dimensions: statue: 77 cm; pedestal: 78.9 cm; base: 22.2 cm; plinth: 15 cm Scanned: 2016 Scanner: Artec Spider This marble sculpture of ‘Puck’, the mischievous sprite...
thingiverse
Remixed from IFlight XL7 V2 TBS GPS Puck Mount by grammo For Iflight XL7 frame (https://goo.gl/Fo1rmg) Added the mount for the BN-880 GPS, you can fix it with an zip tie.
cults3d
Remixed from IFlight XL7 V2 TBS GPS Puck Mount by grammo For Iflight XL7 frame (https://goo.gl/Fo1rmg) Added the mount for the BN-880 GPS, you can fix it with an zip tie.
thingiverse
I created just the holder part with the dimensions to fit my Naza GPS and a generic GPS puck that was in a F450 kit I purchased from Amazon. The countersink hole is about 1mm too short for the M3 socket head screws to be flush with the bottom of...