grove pi case 3d models

If you find it on Onshape, you can use configuration panel to choose between OPi Lite and Opi One and select, whether you want holes for headers in the top of the case. No dedicated antenna hole for Lite, though. Fits well if printed in ABS, other...

... are welcome. 4x M2 x 4mm self-tapping screws to mount the optical sensor (untested) 4x M2.5 x 6mm self-tapping screws to mount the main PCB (untested) 4x M3 x 30mm + locknuts to close the case, making it tamper-resistant with a Torx screw.

Hope you'll like it A 40x40x10 fan should fit in the case fi no heatsinke are installed.if heatsink are installed you can mount the fan on the exterior sideThe fan is a 12v and is connected the to the pin 4 (+5v) and 6 (GND) so it spins quietly and...

A NAS Case based on the X822 by SupTronics and X875 power board by SupTronics. Reference models from https://www.thingiverse.com/thing:4284735/files and https://www.thingiverse.com/thing:4292246 I've included a full model and the model cut in half...

... This case is showcasing: USB ports, Ethernet, HDMI, OTG USB, power adapter, uSD card slot, RESET button, POWER buttons, IR remote control, LED indicators, Microphone, and Audio jack. ... New holes are not perfectly aligned but function adequately.

Since I need a case that allows my drone to lift without exposing wide open ports, I decided to close off the HDMI and one USB port. In hindsight, I would add another 0.5 mm to the hinge side to create an even smaller gap between the pieces. I was...

This rpi case is modelled after a retro gaming console, the name of which is lost to the ages, sourced from old polaroids that andrews mom took when we were kids. Features a USB3.0 hub where the controller i/o would have been, as well as a slot for...

Hope you'll like it A 40x40x10 fan should fit in the case fi no heatsinke are installed. if heatsink are installed you can mount the fan on the exterior side The fan is a 12v and is connected the to the pin 4 (+5v) and 6 (GND) so it spins quietly...

This is a reworking of 0110-M-P's Raspberry Case:http://www.thingiverse.com/thing:922740 Big thanks go out to this genius designer for coming up with such an amazing design. Additional parts for the base are available for download right there.

This is a case to hold a 4 channel relay board. You can either print the 'tight' lid which is held on by friction, or the 'magnet' lid. For the magnets: You'll need 2 8mmX3mm hobby magnets. Glue one in the base and one in the lid. Of course, make...

Grove I2C High Accuracy Temperature and Humidity Sensor

Hi again, I've reworked my original design to fit my Arduino+Network Shield+Seed grove base shield for Air Quality monitoring purposes. That's why I used two 2x1 Grove Seed boards. The sliding cover allows the cables to go inside properly. Two sides...

Simple Pi Zero-W Case with stand with Pi-Hole logo, Camera/No Camera and a wall mount for the Camera Configuration. ... Category: DIY

Updated version of the official pi sound case, now compatible with pi 4. ... - add in out information for midi and audio - add holes for double micro hdmi - usb ports larger for better compatibility with pi 4

This case is for a Bigtreetech PI TFT50 + Raspberry Pi 4. This case requires 4 M2.5 screws and supports the 30mm fans. Although not tested with other version of Raspberry Pi the opening are not design solely for the Raspberry Pi 4. ... There are 2...

I made this project beacuse there weren't cases enough ventilated for Raspberry Pi Zero and Pi Zero 2.I made this simple and compact design.BOM4x M2x10 screws

Remix of racreel's Amiga "Mini" case, but for the Raspberry Pi 4 Raspberry Pi secured with M2.5x3mm screws. Put small rubber feet on the bottom for air flow. ...

This is a set for the Astro Pi case for Raspberry Pi B+ and 2B. ...Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: Normal to High Infill: None

... seamlessly. It works exceptionally well now, even fitting snugly into this robust heat sink case https://thepihut.com/products/aluminium-armour-heatsink-case-for-raspberry-pi-4. ...Note that retro pi still does not officially support the PI 4 model.

Raspberry Pi Case --------------------- Designed by me case for Raspberry Pi. The case includes a diode that indicates device status and an "ON" or "RESET" button. Use ordinary wood screws, such as those shown in the photos, to assemble it together.

Case for Raspberry Pi included in our Raspberry Pi 3 Starter Kit. You can also purchase the case separately. At Digital Factory, we invest time and effort into creating and publishing our designs. Consider supporting us by buying products on our...

This case for Pi-Hole utilizes a Pi-Zero W. The first file provided serves as a reference point only and should not be used for direct printing. When using adaptive layers in Cura, the slide-in lid looks particularly sleek. It imparts a smoother...

This is a detailed 3D image of Lefty Grove's official Hall of Fame plaque proudly displayed at the National Baseball Hall of Fame and Museum, located in historic Cooperstown, New York.

This is a remix of https://www.thingiverse.com/thing:3135520 and a very simple holder for the original Pi Foundation case (see https://www.raspberrypi.org/products/raspberry-pi-3-case/) The design uses a wood screw #4 but is fully customizable. ... You...

... is in inches, so adjust for that. make sure it is 100% solid, no raft or supports. get a sensor from: Seeedstudioshttp://www.seeedstudio.com/depot/Grove-t-3.html?ref=top manylabshttps://www.manylabs.org/product/G0102/ print, glue.... ...go...!!!

This is a concept model I designed after going through the images of Terra Pi case. I really liked the case but they don't ship in my country and even if they ship it would be super expensive. So I came up with my own design and made similar case.

Raspberry Pi case with Pi camera, I have remixed the camera mount to fit Inland's Wide-Angel Fish-Eye Camera Module. This is not my design just a remix to fit the camera that I had. I am only adding the front / cover part of the cam mount. For the...

This is a simple snap together Pi case for Raspberry Pi 3B+ and a Pi camera. The only screws are 2 that hold the lower arm mount but the remaining components nap together. I use this for my CR-10S Pro printer and it it works well and it really simple...

The case is somewhat modular, making it possible to fit either a Pi 3 or Pi 4 by printing the corresponding front plate. There are two tops available – one with and one without a GPIO cutout. Three bottoms are also available: one with no mounting...

I stumbled upon printandplay2k's genesis low poly console, which was actually designed as a Pi case but didn't quite work out as expected. After cutting out the internal components, I rebuilt it to accommodate my Pi 2 model. The top surface required...