gsg 16 handguard 3d models

Cover to replace the holes left after removing the side pic rails on the GSG-16. ...Use the same screws for the rail, and you can use either the forward or rear holes by switching sides.

Cover to replace the holes left after removing the side pic rails on the GSG-16. ...Use the same screws for the rail, and you can use either the forward or rear holes by switching sides.

A handguard for the GSG16, to replicate the iconic look of the MP5SD's style handguard. Free for anyone to redistribute! The dimensions should be: X: 54.833mm Y: 60.225mm Z: 187.294mm I've included 2 versions. A full sized handguard, and...

I made an adapter to fit the gsg16 for use of the Cyma aluminum RIS MP5 hand guard. It might hurt your thumbs as it snaps firmly into place. There is no wobble and the hand guard does not move when installed. Unrelated from the print, the right...

Glue parts together, make sure to sand inside thoroughly. ...Barrel sleeve for GSG-16.

Magazine coupler for GSG-16. ...It uses a M5-0.8 x 45 mm Metric Socket Head Cap Screw and a M5 nut to secure the coupler together.

made a selector switch for my gsg 16 so I can use it with my thumb without breaking grip uses the same screw from the original one you might have to mess around with the scale to get it fitting tightly on your gsg16 depending on ur printer. ...I printed...

I wanted wood furniture for my GSG-16, here is my attempt. You do not need glue for the front handguard, it wedges together snug enough without it. If you are going to glue it, I recommend only gluing the handguard and bottom part as gluing the whole...

This is a simple filler for those who would prefer to remove the top hand-guard rail on the GSG-16. ...It should just pop in and use the same screws that you use to secure the top rail.

Couldn't find a magazine rack on here for the GSG-16 .22 so I scratched this up real quick. Simple print with no supports and use infill as much as you please. ... Hope this helps!

Slides perfectly over the existing fake suppressor on a GSG-16. Pressure fits so no extra hardware needed to install. See images for before and after pix. Glued the two pieces together with superglue and works like a charm. ... I printed with 3 shells...

I made this replacement GSG 16 rear sight because it tends to break easily. I found that the 4mm hole works best, but there are a few other sizes available. The screw will be very tight to fit in, but that is necessary to ensure that the sight...

This is to replace the OEM rear sight on a GSG-16 using the existing hardware. I used a M2 screw to secure the two parts together, but I sized it so you can use the screw from the OEM sight. I recommend printing in PetG for the UV protection. Picture...

An Animation for GSG

Mp5 style cocking tube and top rail delete for GSG-16 .22 rifle. The top rail is meant to be placed beveled side down, you might need to insert a shorter front screw to avoid impeding the bolt. ... Remixed from BlitzLab ...

Shooting the GSG-16/522 rifle is fun. It's east to dump your magazine quickly. So to save your thumbs, this handy little device will speed up the process. Simply slide down the magazine on top of the follower and press down releasing the tension on...

Sight mount to mount a traditional hk diopter rear sights to the GSG-16. It uses the screw that secures the rear sight on. Make sure not to over-torque it. You can use the screw used on the OEM hk diopter rear sight to secure the rear sight to the 3D...

This is a 16-inch handguard for the FGC-9. This can be useful if you want to put a 16-inch barrel on it to turn it into a rifle. Of course, you need to get a longer barrel and not only use a long handguard. This will fit right on the original...

This can be useful if you want to turn the FGC-9 into a rifle (16-inch barrel) to put a stock on it or if the ATF bans pistol braces. Of course, you still need a longer barrel and not just the handguard. For any reviewer from Thingiverse, This is...

AR15 Handguard

Pokemon GSG CARD Holder

AR15 M4 HANDGUARD

Requires one short screw to attach, might not be compatible with drum magazines. ...Best printed at 0.08 layer height.

These are the parts I made to extend my GSG-522 to appear more like a full length HK G3. This includes a barrel shroud, cocking tube, cocking bar and barrel clamp. ...You will still need a screw for the barrel clamp and a HK G3 handguard that will need...

it's a complete 165mm ris for an gsg aisoft's mp5

The model for the handguard is one piece, i chose to print mine in three pieces so that i could use the "fuzzy skin" function in Cura to give the center section some texture. If requested, i will upload a selection of handguards that are sectioned...

This is a speed loader for all magazines save for the drum style for the GSG 5 and GSG 522. It uses a friction fit to keep the retaining spring down, and the tolerances should be tight enough to not require pressure to be held on the speed loader it...

This is a speed loader for all magazines save for the drum style for the GSG 5 and GSG 522. It uses a friction fit to keep the retaining spring down, and the tolerances should be tight enough to not require pressure to be held on the speed loader it...

GSG-5 magbase - a clone of the original. Can be used as drop-in replacement. Also contains "sideplates" and "sleeve" that make it possible to remove the screws and (on some models) nuts altogether so you can disassemble and assemble the magazine...

Magazine base plate retainer for Sig Sauer Mosquito/ GSG Firefly. I was installing the +4 follower I found on here (works great by the way-thing no. 3321753) and this piece slipped out from under my thumb and entered a hole in time and space never to...