gsg 5 3d models
569788 3d models found related to gsg 5.thingiverse
GSG-5 magbase - a clone of the original. Can be used as drop-in replacement. Also contains "sideplates" and "sleeve" that make it possible to remove the screws and (on some models) nuts altogether so you can disassemble and assemble the magazine...
thingiverse
This is a speed loader for all magazines save for the drum style for the GSG 5 and GSG 522. It uses a friction fit to keep the retaining spring down, and the tolerances should be tight enough to not require pressure to be held on the speed loader it...
myminifactory
This is a speed loader for all magazines save for the drum style for the GSG 5 and GSG 522. It uses a friction fit to keep the retaining spring down, and the tolerances should be tight enough to not require pressure to be held on the speed loader it...
thingiverse
Kimmon Keeäskee-Kisko™ A snap-in 1-piece picatinny rail for GSG-5. Perfectly fitted. Well, a piece of electric tape could be used as a shim IF your printer is off-spec. Snaps in place, requires a screwdriver or something to detach. (I will -...
thingiverse
A fake, non-functioning suppressor-lookalike for the GSG-5 and GSG-522 .22LR rimfire rifles. It's much shorter than the original - the can is 103mm long. This was created because the soviet EU's gun ban directive resulted in a change in the...
thingiverse
External magazine limiters for standard GSG-5 / GSG-522 stick magazines. Just glue in place or use duct tape or whatever. No disassembly required. In Finnish hunting legislation the modification does not have to be impossibly hard to remove and...
thingiverse
A drop-in replacement magazine basepad for GSG-5 standard magazines. Also a "sleeve" for attaching said basepad (or the original basepad) without using screws. Just wrap something - electric tape, iron wire, rubberband, ziptie or whatever -...
thingiverse
Mp5 style cocking tube and top rail delete for GSG-16 .22 rifle. The top rail is meant to be placed beveled side down, you might need to insert a shorter front screw to avoid impeding the bolt. ... Remixed from BlitzLab ...
thingiverse
Requires one short screw to attach, might not be compatible with drum magazines. ...Best printed at 0.08 layer height.
thingiverse
Glue parts together, make sure to sand inside thoroughly. ...Barrel sleeve for GSG-16.
thingiverse
Magazine coupler for GSG-16. ...It uses a M5-0.8 x 45 mm Metric Socket Head Cap Screw and a M5 nut to secure the coupler together.
thingiverse
Cover to replace the holes left after removing the side pic rails on the GSG-16. ...Use the same screws for the rail, and you can use either the forward or rear holes by switching sides.
cults3d
Cover to replace the holes left after removing the side pic rails on the GSG-16. ...Use the same screws for the rail, and you can use either the forward or rear holes by switching sides.
thingiverse
These are the parts I made to extend my GSG-522 to appear more like a full length HK G3. This includes a barrel shroud, cocking tube, cocking bar and barrel clamp. ...You will still need a screw for the barrel clamp and a HK G3 handguard that will need...
thingiverse
made a selector switch for my gsg 16 so I can use it with my thumb without breaking grip uses the same screw from the original one you might have to mess around with the scale to get it fitting tightly on your gsg16 depending on ur printer. ...I printed...
thingiverse
Magazine base plate retainer for Sig Sauer Mosquito/ GSG Firefly. I was installing the +4 follower I found on here (works great by the way-thing no. 3321753) and this piece slipped out from under my thumb and entered a hole in time and space never to...
thingiverse
I never liked the faux silencer on my GSG-522, so i decided to design an HK91 type conversion that makes it look like a proper rifle and not a neutered SBR. You will need a 4-40 screw and nut and a 6-32 screw and nut (or metric equivalents) to...
thingiverse
Pieces pour transformer son GSG 522 type mp5 de cyberun en modele mp5 pk custom en batterie lipo 7.4 V
thingiverse
This is a simple filler for those who would prefer to remove the top hand-guard rail on the GSG-16. ...It should just pop in and use the same screws that you use to secure the top rail.
thingiverse
Couldn't find a magazine rack on here for the GSG-16 .22 so I scratched this up real quick. Simple print with no supports and use infill as much as you please. ... Hope this helps!
thingiverse
Slides perfectly over the existing fake suppressor on a GSG-16. Pressure fits so no extra hardware needed to install. See images for before and after pix. Glued the two pieces together with superglue and works like a charm. ... I printed with 3 shells...
thingiverse
I made this replacement GSG 16 rear sight because it tends to break easily. I found that the 4mm hole works best, but there are a few other sizes available. The screw will be very tight to fit in, but that is necessary to ensure that the sight...
thingiverse
This is to replace the OEM rear sight on a GSG-16 using the existing hardware. I used a M2 screw to secure the two parts together, but I sized it so you can use the screw from the OEM sight. I recommend printing in PetG for the UV protection. Picture...
thingiverse
I wanted wood furniture for my GSG-16, here is my attempt. You do not need glue for the front handguard, it wedges together snug enough without it. If you are going to glue it, I recommend only gluing the handguard and bottom part as gluing the whole...