gso focuser 3d models

I needed a dustcover for my Explore Scientific Refractor Telescope, good thing there is 3D printing :)M68 x 0.75 thread for Hexafoc or maybe other focusers Print it in 0.1mm layer height for a clean thread

This is a replacement grip for the focuser on a Celestron C-14. I tried it on my Meade LX90 and it fit also, so it may be more universal. ... I use TPU when printing it.

This is the story of myFocuserPro2M DRV8825 focuser controller, built from scratch on the project at https://sourceforge.net/projects/arduinoascomfocuserpro2diy/files/myFocuserPro2M/. The printed circuit board can be downloaded from...

This is a focuser for a Celestron C11, using: - 1 Nema17 Stepper motor - 2 M4x 20mm Hex Head Screws and - 2 M4 nuts for the lateral screw holder - 2 M3x10mm screws with nuts for case holding - 2 M3x10mm screws for stepper motor - 2 M3x5mm screws with...

The controller is based on anat's Leonardo-based controller, found here: https://www.cloudynights.com/topic/594658-pnp-focus-the-simplest-ever-arduino-focus-controller/. I used the NEMA 17HS13-0404S-PG27 motor that anat referenced in his post and...

... perfectly suited for seamless integration with the 28BYJ-48 motor. Meanwhile, the focuser gear sports an impressive 40 teeth, accompanied by a 4mm screw hole and a 9mm rear hole with a precision countersink to ensure effortless centering.

Probably yes and due to the fact that your equatorial mount is not as stable as you expected and just by touching the manual focuser, you get a very shaky image in your eye piece. You can find here details about my project. I added also a 3D STL...

... software used for this focuser is Ardufocus, developed by J.Brazio, whose work is greatly appreciated. The Arduino is connected to a Raspberry Pi via Ekos/Kstars/Indi software, facilitating seamless control and automation of the focusing process.

An adapter from Thingiverse connects the camera to the focuser tube, fitting perfectly on its 32mm OD (1.25" approx.) but not compatible with standard 1.25" or 2" lens mounts. Print settings include rafts, supports, and a 0.1mm resolution. The...

Created to go with the Newtonian Telescope "Newton To See Here" found at https://www.bigbigspace.com/telescope/n607-newton-to-see-here The focuser also requires 3x 85mm steel or brass slides, 1/8 inch by 1/2 inch. 4x 12x6x4mm bearings 1x 4mm...

This is the box I'm using for my focusers. They are based on Ardufocus (https://ardufocus.com/). This specific build uses: - Arduino Uno - "Driver" ULN2003 - Stepper motor 28BYJ-48 - 4x M4x12 screws with nuts - 4x M2 screws for fixing boards to the...

Enclosed Box for Arduino Nano, Motor Driver and Electronic Focuser Motor \r\n DIY Built, Includes Enclosure, Enclosure Lid and Pulley\r\n The belt I used is a 2.5 mm pitch toothed belt\r\n Project link:...

This is a precision-crafted bracket I designed specifically for motor focusing with my telescope, tailored to fit the Skywatcher Startravel 102 focuser like a glove, holding a Nema 17 PG25 stepper motor securely in place. The design may also work for...

ABSFCS-1.25" Crayford focuser... The latest version, 0.1b, is now being upgraded. ... The essential components of this upgrade include: 624zz bearings - a total of six M4 bolts measuring 25mm each - four in number M3 bolts measuring 30mm each - also...

Focuser 1.25 inch for telescope prints with Prusa i3 settings optimized for precision. Printer resolution is set at a precise 0.2 mm to ensure crisp details. ...Infill density is carefully adjusted to 20% for added strength and reduced material usage.

### The Focusino is an Arduino based, compact telescope focusing device that is homebrew friendly (single sided PCB) which uses simple and easily sourcable components/parts. **Small form factor (51mm x 51mm x 46mm)** Please checkout the Github...

The coupler has a mechanical fuser (4 thin long bars) that helps to avoid physical damage of the telescope focuser in case of end point is reached (no limit switch was used). No nuts were used, all bolts were heated and screwed into the parts. The...

The coupler has a mechanical fuser (4 thin long bars) that helps to avoid physical damage of the telescope focuser in case of end point is reached (no limit switch was used). No nuts were used, all bolts were heated and screwed into the parts. The...

Every manual focus lens features helicals for its focusing mechanism. If your lens front element does not rotate when focusing, it is likely that your lens has two sets of helicals - one with left-hand turn and the other with the more conventional...

Focuser for the Meade Polaris 127 the original one is bad, the Bore is conical, and only one bearing surface. Result: the Eyepiece wiggles New design: Straight Bore, three bearing surfaces. As for the bearing surfaces, you will need expended...

The focuser is designed to fit any standard 1.25" telescope or instrument. For a 2" version, please visit http://www.thingiverse.com/thing:1904663. ... Print Settings: - Printer: FF Dreamer - Rafts: Not required - Supports: Not necessary - Resolution:...

DSC-V3 for Dobsonian GSO 10” Improved version of “V1.2 DSC - Digital Setting Circles / Alt-Az.Push-To for Dobson GSO 10" telescope and others” at https://www.thingiverse.com/thing:3484570 See https://www.thingiverse.com/thing:4358327 for electronics!...

This is the box I'm using for my focusers. They are based on Ardufocus (https://ardufocus.com/). This specific build uses: - Arduino Uno - "Driver" ULN2003 - Stepper motor 28BYJ-48 - 4x M4x12 screws with nuts - 4x M2 screws for fixing boards...

This support enables mounting a stepper motor onto a scope, making it possible to fine tune focus using an Arduino without physically touching the scope and risking vibration issues. To achieve this setup, I've employed rubber bands to securely...

2in Crayford Focuser specifically for 3D printing.If you are using VHB/double sided tape to stick he bearing runners down to the surface of the draw-tube the present offsets are correct on the feature "tune bearing surface depth" on file CRAY_2in...

If like me you want to adapt an electrical focusing system to your telescope, you've landed in the right place. It cost me 20€ compared to 100€ in the shops! If the sprockets are well installed, there won't be any play and it will turn out very...

This is the box I'm using for my focusers. They are based on Ardufocus (https://ardufocus.com/). This specific build uses: - Arduino Uno - "Driver" ULN2003 - Stepper motor 28BYJ-48 - 4x M4x12 screws with nuts - 4x M2 screws for fixing boards to...

Cette pièce permet de faire la mise au point de la camera auxiliaire sans rotation de champ.Astuce : avant montage il faut roder les les pièces vissée et les enduire d'un peu de graisse au téflon avant montage.This accessory makes it possible to...

Part #18 The Focuser Body of the OSA Ultrascope project. I recommend visiting https://www.wevolver.com/osa.projects/ultrascope/main/description/ to get the lowdown on everything you need to build your Ultrascope and learn more about this awesome...

This is an exciting little project I'm working on - adding remote focus capability to my stock focuser. My trusty 80mm Skywatcher refractor will soon benefit from this upgrade. To bring it all together, I printed the remote focus mechanism in PLA at...