guan yu 3d models

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft: (note skipped groove, blue arrow) Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

The tolerances on these can be somewhat tight, but they came out beautifully on my Bambu X1C.Model specific notes follow:cards_box_1.stl, cards_box_2.stl - Print one of each. You can add color on layer 4 or 5 (depending on line height) to make the...

You could group them in Tinker and make a single/twin mega model - love that Tinker feature! Support is required in places due to geometry, but it's very simple square profile support that is easily removed. I always try to avoid it, but not at the...

 I am hacking stuff together in Tinkercad, so parts of the original Voron panel retention clips and hinges were used in creating these.I plan to make matching latches in the future, but for now am using these panel...

A lot of the model are just perimeters or solid bottom/top layers. The pass-through holes for the cables create small bridges first and they are closed first, and then the top cover is printed. ...So I made a few arrangements to allow decent printing...

The COMPLETE Bonegnasher Gnolls I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Gnolls were spawned by the Demon Raz'n'guul, born from a rotten tooth of the corruption god...

For other sizes of tube or different grid arrangements, you can use the Thingiverse Customizer to remix your own version (the recommended way, so others can benefit from your work) or download the model and use the OpenSCAD Customizer (available in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

;-) How did I end up with two of these devices? At first I bought the 2TB version and wanted to replace the HDD with a 5TB model. I tried several things, but nothing worked. With vaccation ahead, I ordered a second device with 3TB. The electronics of...

**My Tinkercad-works:** [Coverplates + Hinges + Z&Y-FrameChainmount + Connectos-Hub + cutout-stamp](https://www.tinkercad.com/things/60ksBr4wvsb-s8-pro-coverplate-hinge/) [Hotend Mount + Y-Axis Chain...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

It should be possible to customise the model by changing a global variables that represent the battery dimension and straps width- holes for the LED indicators- reducing the number of screws- creating the cases for wider range of IMUsPlease let me...

None of these models should need any support, I try to avoid them if at all possible, but you will need to be able to bridge somewhat decently. I personally used Overture Easy Nylon, it's very stiff for a nylon that doesn't seem to creep and...

(Rotate these angles accordingly if you rotate the model.) This way, you will have two layers of crossing extrusions in the spine folds. This makes for much stronger, long-lasting book hinges.</p><p>For<strong> print-on-print</strong> technique (used...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! Update 1: My Start and End G-codes in Cura working well with this firmware: ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

- Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

A .3mf file is available along with the STL models.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it works best to drill a first hole and then insert a screw into that...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Again tilt the drawing slightly, noting that you have the right corner vs the model orientation. It can get a little confusing. Save the Sketch 4. The spacer should automatically be tapered to match the corner height because the angled plane adjusts...

The first number at the end of each model's filename is the size of the PVC post that the adapter is intended to go on top of, the second number is the size of the PVC pipe that the finial would normally go on. I have a collection of Halloween things...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...