gy 521 3d models
687 3d models found related to gy 521.thingiverse
... Pitch axis, the cutoff frequency of a filter with the Roll axis, and the resonance of the same filter with the Yaw axis. I 3D printed an enclosure for the GY-521 and I wear it like a watch using 2 velcro cable ties. ... The PCB files are here.
thingiverse
Customized version of https://www.thingiverse.com/thing:2758851 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2758851
thingiverse
I use the Arduino Nano in conjunction with a GY-521 Accelerometer (MPU6050) for this. Since the accelerometer board has 2 mounting holes but one of them is unusable due to a directly adjacent component, I quick and dirty designed and printed a...
cults3d
I use the Arduino Nano in conjunction with a GY-521 Accelerometer (MPU6050) for this. Since the accelerometer board has 2 mounting holes but one of them is unusable due to a directly adjacent component, I quick and dirty designed and printed a...
thingiverse
This is a small support to glue on standard donkeycar. Accelerometer/gyro is this one: https://fr.aliexpress.com/item/1028067742.html Probably not the best. Need a SUPER quiet (stable with no spike) power in. ...
thingiverse
This is a support to calibrate an accelerometer MPU 6050. You have to slide it all the wayin to have the center of the sensor in the center of the support. ...At this point you can tilt it at 45/90 degree in the two axis.
thingiverse
this model will hold the gy-neo6mv2 sensor and the antena with a good tollerance
grabcad
GY-GPS6MV1 is a low energy GPS module for Arduino and similar microcontrollers. ... Current version got as close as possible minus the wire that connects the antenna to the board which was left as a spline.
grabcad
Swivellink P/N AFSB-521-C-DI Fits: Cognex Dataman 300 and Insight 7000. ...Mounts to AFSB-1 or AFSB-1XS.
thingiverse
Kalibrierhilfe GY-801 ==================== Kalibrierhilfe um den IMU GY-801 einfacher kalibrieren zu können.
cgtrader
High quality 3d models Plants collection 521 A unique collection of plants can be used for exterior and interiors
thingiverse
Case for GY-63 Atmospheric Pressure Sensor Module (MS5611 sensor) Print Settings Printer Brand: RepRap Printer: i3 Rafts: No Supports: No Infill: 100%
grabcad
The modules from ebay : https://www.ebay.de/itm/Lichtintensitat-Sensor-Modul-fur-Arduino-GY-30-3-5V-BH1750FVI-I-C-ADC/182551839081?hash=item2a80f00169:g:gmgAAOSwhvFZBLVD
cgtrader
Skyscraper Cityscape 521 3D ModelsHigh detailed 3d building.Previews were rendered with vray mat and light.The file has all lightning setup and texturing ;multi layer phososhop PSD file included
thingiverse
I added this part in order to install the Light sensor GY-30 to my Weather Station. The sensor It is not directly exposed to the sun but is protected by rain. ...
thingiverse
This is a convenient port housing for the GY-63 / MS5611 barometric pressure sensor. ... It's designed to take a 9.8mm quick release pnematic fitting (1/4" hose) and it has an optional (drill through) second port tube for a differential pressure sensor...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=496248 Instructions Using the following options: Shield = 3 Primary_Weapon = 2 Pilot_Skill = 4 Text = Y-WG GY Hull = 5 Agility = 1