hakko 808 parts 3d models
551292 3d models found related to hakko 808 parts.thingiverse
Annoyed by your beloved Hakko 808 desoldering gun refusing to stand up for itself? This wall mount holder will hold it for you. (without melting! It holds by plastic parts of the body and doesn't get too close to the business end) Post-Printing...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Loop_character = U center = 50 twist = 1 Loop_x_position = 11 height = [9,8,7,8] Loop_font = Chewy Loop_y_position = 3 Rotation = 150 Text = #808...
thingiverse
slotcar chassis for action cam - 808#16 made for ball bearings and 2mm axles guide needed carrera go motor or any other FF030 motor 28tooth spur gear m0.5 8 tooth pinion m0.5 (one with 1,5mm for motor, one with 2mm for intermediate axle) i´m using...
thingiverse
... :) Enjoy! Instructions The mount was made by curve tracing a photo of the 808 circuit board. ... If you want to use the 808 with the case on then just use the bare V959/V222 bracket instead of this one and some double sided foam tape like 3M VHB.
prusaprinters
This system is currently designed to work only with this version of the 808 (there are many).Here are the 3D Print files for making your own Cineroc Mini 808, I probably will be updating the parts as I tweak and improve them.I print most of the parts...
thingiverse
Camera_Sled_v2.stl. Naturally, if you've already downloaded the full build, you only need to download [this one part](https://www.thingiverse.com/download:6441418) Mini Cineroc 808 Mike Dorffler designed for Estes Industries the 'Cineroc' a super 8mm...
thingiverse
This is a remake of the original bobbin shaft for a Hakko solder reel holder 611. ... This is a replacement for Hakko Part 999-218.
grabcad
IPG Laser diode. ...Average Optical Power (CW ): 15 W; Emitting Wavelength: 808 nm.
thingiverse
*All Units are in Metric Unless Specified* Layer Height: .2mm Wall Thickness: .6mm Top/Bottom Thickness: .8mm Infill: 10-20% Infill Pattern: Grid Print Temperature: 220 Bed Temperature: 55 Diameter: 1.75mm Flow: 100 Enable Retraction: YES Print...
thingiverse
One part is the actual case the camera sits in with two holes for self-tapping screws, the other is the top that keeps the camera from falling out, and the third is the bottom that is made for a 4" OD rocket airframe. ...
thingiverse
1 - 808 based keychain camera (most should work with this design) 1 - BT 50 based rocket (like an Alpha) OR... ... 1 - BT 50 (about 8") 1 - BT-20 motor tube 1 - Motor retention clip 1 - Engine block 1 - shock cord 1 - Parachute 1 - Nylon Zip...
thingiverse
... straight rip wasn't manifold and it had to be repaired, but it should be fine for printing. I added an alternative version with flat feet, for easier printing. Original model: https://www.deviantart.com/joshu76/art/Hi-Fi-Rush-808-Model-947968887
prusaprinters
For most kids it was overly complicated to use and to get good results but the opportunity to see the world from the view of your rocket drove many to send the Camroc aloft. If you want to read more about the original Camroc - here's a great blog to...
thingiverse
Holders for the 808 Keycam models with hole 4mm, outside round 10mm, 5mm thick, fixed with an elastic band... ... with mounting plate, holes 4mm distance 18mm SSG Gimbal http://www.rcgroups.com/forums/showthread.php?t=1793759
thingiverse
A new base for mjruzzi's 808 Camera Case Cover. This base is designed for a 3" diameter rocket. ...Print Settings Printer: MakerFarm Prusa i3 ...