hall effect sensor housing unit 3d models

Housing build for Adafruit MCP9808 Temperature Sensor. With attached OpenSCAD file everything is customizable, especially size of screws to close and size of opening for connection cable. ...But can also easily adapted for other breakout boards.

A remix of the run-out sensor housing from Creality that has had issues with false triggering. ... It is highly recommended to print the test file first to see that your printer can produce clean fixtures for the components.

This project involves developing a 4-way ultrasonic sensor housing, specifically tailored for my dissertation research. ...The focus is on utilizing the HC-SR04 module to accurately measure distances on a quadcopter platform.

I am building a Housing for Affordable Capacitive Soil Moisture Sensors paired with a Wemos D1 mini. I use Tasmota to transmit the readings directly to Node Red. ...This Project remains an ongoing Work in Progress.

The small mount is designed to be easily secured using a single 6-32 bolt that passes through both the sensor and the housing, allowing for seamless integration with Tetrix or Actobotics components.

A remix of the run-out sensor housing from Creality that has had issues with false triggering. ...It is highly recommended to print the test file first to see that your printer can produce clean fixtures for the components.

A very simple housing for DHT11 sensor that allows mounting on a surface or panel. I used a protoboard or perfboard to connect the sensor to the wire. The board also provides the bottom support for the sensor, while the top is supported by a ridge in...

The capacitive soil moisture sensor v1.2 requires a housing to protect its electronic components. This housing will not be fully waterproof since the socket remains exposed on top. It's designed for indoor use only. Two versions of the housing are...

To install this upgrade, you'll need to secure the spare tube and the filament run-out sensor using the bolts provided in the housing that comes with it. ...For added stability, consider applying glue or using zip ties if the assembly feels too loose.

Additionally, several similar housings are available online, but they often failed to consistently depress the sensor switch reliably. To address this issue, I designed my filament path at an angle, ensuring that the switch is always properly...

I decided to mount the sensor to the frame instead of the magnet to help preserve the device (Slamming of the door may end up loosening the battery or damage the electronics) It also enable you to remove the sensor for the reset button or change the...

Design intended to reduce and/or prevent filament from getting hung up inside the housing of the filament sensor/switch housing. Uses existing mounting bracket and mount in the same two screw locations, but the mounting bracket will now mount...

Design intended to reduce and/or prevent filament from getting hung up inside the housing of the filament sensor/switch housing. Uses existing mounting bracket and mount in the same two screw locations, but the mounting bracket will now mount...

And also more consistent results if I had hall sensors instead of switches for homing on the 3 towers. ...After these videos, I did find I could slow down the probing by modifying a line in marlin_main.cpp, so if you want to do the same, look for:...

This is a custom housing for the Fibaro FGBS-321 Universal sensor, designed since no commercial housing was available. The sensor is used for temperature sensing, so the bottom opening fits exactly with one servo type plug and a JST connector that...

https://www.thingiverse.com/thing:454584 This housing/mount holds the Mulier PCB vertically, rather than horizontally, to help keep debris off the photo sensor diode array itself and away from the LED that shines on the diode array. This housing...

I wanted an effective, adjustable detection device for use with my DSLR and hybrid cameras for wildlife photography.After looking at the various PIR (passive infrared sensor) detectors available, I decided to go for one from Camtraption :...

... into place, and I recommend taping it firmly so that no water can penetrate. I also encase the sensor in a mini-ziplock bag for added protection. After running this setup for more than one year, the sensor remains functional and works flawlessly.

I am so tired of Creality Filament Run Out Sensors being so difficult to load that I designed a housing with confined path that uses the Creality V2 internal sensor component. I printed on a resin printer for accuracy and smoothness. I printed on...

This housing fits the sensor taken from an RGB LED remote control system perfectly, providing ample space for an Infrared LED to operate a controller using home automation technology. The IR LED is cleverly concealed, ensuring it doesn't interfere...

This is a basic housing for the 3.3 Volt Ultrasonic Sensor RCWL-1601, which might be used in place of the HC-SR04 (which is 5V). The benefit of the RCWL-1601 is that it may be wired directly to a Raspberry Pi without resistors, so you don't need...

You need: - a Prusa MK3 - a Bondtech extruder for Prusa mk3 - the upgrade kit for MK3s (coming also with the MMU2 to MMU2s upgrade kit sent to MMU2 owners) for the new IR sensor, the magnets, the steel ball and the sensor nut - 2 M3 square nuts - 3...

We are currently building a measuring device to measure the gases produced during composting. ...Among other things, we want to use MQ sensors for this. The housing is to be connected to the bioreactors via a hose. ...Hence this "airtight" case.

I created a small housing to hold an ESP8266 together with a Si7021 to form a WiFi temperature and humidity sensor. ...More details on the source code and how to setup a the IoT main server can be found on my blog...

This is a housing for a BME280 sensor module to accompany my design https://www.thingiverse.com/thing:4857472 and which I am using to measure temperature and humidity outside my greenhouse. The lid is a snap fit onto the main case. ...

This housing is engineered to integrate seamlessly with yyh1002's Modular Mounting System (https://www.thingiverse.com/thing:2194278). It specifically accommodates a Sharp IR Distance Sensor GP2Y0A21YK0F. ... Print using 35% infill and support, but be...

Housing build for Adafruit MCP9808 Temperature Sensor.With attached OpenSCAD file everything is customizable, especially size of screws to close and size of opening for connection cable. ...But can also easily adapted for other breakout boards.</p>

... on the outgoing water was incorrect. In order to get a more accurate reading I designed this housing for the temperature sensor. ...Now the readings are correct and not affected by surrounding heat, especially radiated heat from the laser tube.

A MAP sensor housing for a 2.0-litre, turbocharged direct injection engine featuring advanced technology and precision engineering is available as a replacement part. This component plays a crucial role in monitoring air pressure to optimize engine...

I optimized the housing setup, eliminating the need to cut a PTFE tube for the sensor connection. Now, only two small tubes are required for in-and-out access, making the process significantly simpler and less stressful. ...This streamlined approach...