ham radio 3d printer projects
1946042 3d models found related to ham radio 3d printer projects.grabcad
This is home made Optical Encoder. ...The prototype reproduced using Makerbot Replicator 2 3D printer. I use it to control frequency of amateur radio transceiver. ...Covers and encoder disk have to be printed using black filament to avoid misfunction.
cgtrader
This is a model of a Vintage WW2 Era HAM Radio. Textures maps and UV data are included. 4k texturemaps for metal/rough setup. 129568 polys. Multiple texture sets. If you have any questions feel free to message me! ...
thingiverse
I hade this for my 3D printer but should work for kinds of equipment live a Ham radio. ... https://www.youtube.com/watch?v=dOlkYxDetz8 Power Socket / Switch I used ...
cgtrader
Ham Radio Transceiver. Game Ready Model. ... Transceiver 2192 Tris + LOD 176 Tris Microphone 1547 Tris + LOD 446 Tris Speaker 437 Tris + LOD 113 Tris 2048x2048 Textures Specular map (in alpha channel) Normal map Reflect map (in alpha channel)
grabcad
A suitable stand in for the HAM radio made by ICOM. ...I used this to create my 3D printed mounting brackets.
thingiverse
Ham Radio Antenna Coupler!! For a 1 Inch OD tube! ...https://www.youtube.com/watch?v=dv5FACcWDwY&lc
thingiverse
Micro support for CB and ham radios. ...Designed specially for no drill and use film of double side in cars or fournitures.
thingiverse
Print body and lid separately for better results. ... Both body and lid should be printed vertically, standing position. Updated Version to be updated by user demand. Ham Radio Antenna Enclosure (BF-F8HP - BaoFeng)
thingiverse
This is to redirect the sound from the top mounted speaker of a ham radio towards the operator. ...There are indents on the bottom for 5mm x 1mm magnets.
thingiverse
This is a case for a Duplex Ham Radio hotspot. Put the Hotspot hat together with the raspberry pi and then put it in the case. ... The screws are M2, you will need 6 of them.
thingiverse
A three level stand for ham radios with a bale. Made for a Yaesu FT-857, this will work with many other radios. There are indents on the bottom for stick on rubber pads to prevent sliding. ... UPDATE 12 November 2019: added sloped side to the short...
thingiverse
These are parts for a Ham Radio Manpack, which uses OpenBeam for the structure, and laser cut acrylic for the panels. It is designed to sit inside a Voodoo Tactical 2 Tier pack (Update Jan 2020 - this is no longer offered). This is designed to host a...
thingiverse
I wanted a way to set my microphone on the cart I use for my ham radio gear. It has 13mm rods along the edges, so I wanted it to just 'clip' onto the rod. It prints OK but it doesn't clip as well as I would like and the fit is very tight. But it...
thingiverse
... PD365. ...After getting myself a Baofeng UV-5R i realized it fits just as well. it locks on to the "feet" of the radio so it won't slip out. Print Settings Printer: Prusa i3 Rafts: No Supports: No Infill: 10% Notes: Printed in PLA. ...Post-Printing
cgtrader
Game Ready Model. ...Ham Radio. Antenna Controller. ... Conrtoller 964 Tris + LOD 98 Tris 2048x2048 Textures Specular map (in alpha channel) Normal map ON/OFF Mode
cgtrader
Game Ready Model. ...Ham Radio Monitor Scope. ... 1914 Tris LOD 94 Tris 2048x2048 Textures Specular map (in alpha channel) Normal map ON/OFF Mode
prusaprinters
This is my prototype version of a DIY Loading Coil for HAM Radio. <strong>(UNTESTED)</strong></p><p>It is a glue together design for the 3 main coil parts (bottom_coil, main_coil, and top_coil). </p><p>The coil caps, and radial ring can be...
thingiverse
For inspiration, another weekend project completed. ...After too much tangle and mess with my always so «temporary» field power setup, I created and 3D printed my own little power distributor. Makes it much more tidy. ...Even works in the shack.
thingiverse
I wanted another way to label my coax for my radios leading into the coax selector switches. This was some of my first designs on Tinkercad. No special settings for printing. I used PLA. ... This was printed on the Anycubic Vyper.
thingiverse
This has holes for mounting the radio face plate to it, but it slips into the card holder that is in the well of the console. Seems to work fairly well. Used Fusion 360 to model it, and sliced it with Slic3r. Printed it on end, 190 mm high, on a...
thingiverse
4 x M3 x 12 mm wood screw ( used to fix two support to the base ) Print Settings Printer Brand: RepRap Printer: Prusa I3 Rework Rafts: Yes Supports: Yes Resolution: 0.5 Infill: 10% Notes: I used PLA to print the key. ...Post-Printing After printing...
thingiverse
Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: Yes Supports: Yes Resolution: 0.2 Infill: 100% Notes: I made the prototype (this one) with 30% fill and it was really strong, but since there is literally 0.1 mm gap between the walls, I...
cults3d
Alternative vfo knob for Yaesu FT817 ham radio. ...It has a side hole for inserting a locking screw.
myminifactory
Contains 6 props and 1 Ham Radio Operator 35mm scale Check out my patreon to get the newest miniatures released. ... patreon.com/sarksfoundry
cults3d
Lightweight, pocket-sized, portable windom antenna support for ham radio. ...Toroids used in my configuration are very small (T80) and also it is the windings wire.
thingiverse
This is designed to hold an external mic for stationary ham/CB radios at your radio bench/table. ... The holes are 2mm in the diameter to hang the holder via nails.