harbor freight torch holder 3d models

Replacement slide on 3/8 drive socket holder insert for the Harbor Freight magnet organizer. ...Friction fit rather than ball bearing snap but it works fine.

a basic screwdriver holder to hold the cheap @$$ blue multi-screwdriver from the good ol harbor freight. printed with the flat side down. designed to be affixed with a 3m command strip. ... harbor freight screwdrivers like this have really poor...

Based on Harbor Freight Clamp Holder by Fillitup309 but modified to print as a single piece with no supports. I barely made any changes at all. ---- Organize your Harbor Freight clamps. 4, 6, or 8 clamp holder (6 should be short enough to print on...

This is a holder screws to the wall to fit a small flashlight from harbor freight (those free ones with the coupon). ... We used it for placing emergency flashlights near our entrances and on our powder coating setup.

But the Harbor Freight glove box doesn't fit very well into the Harbor Freight glove dispenser... Go team... Problem solved. ... This glove holder has three countersunk mounting holes and it's even got "GLOVES" printed right into the front of it in...

A stand for a Harbor Freight Multimeter. ... I added some pockets for magnets to the stand.

But the Harbor Freight glove box doesn't fit very well into the Harbor Freight glove dispenser... Go team... Problem solved. This glove holder has three countersunk mounting holes and it's even got "GLOVES" printed right into the front of it in...

I designed this Harbor Freight flashlight holder so when I change tools on my machine at work, I can see in the dark tight areas. This holder uses 5mm x 5mm x 3mm thick magnets. ... I have also included the Fusion 360 file so anyone can change it...

I designed this Harbor Freight flashlight holder so when I change tools on my machine at work, I can see in the dark tight areas. This holder uses 5mm x 5mm x 3mm thick magnets. ... I have also included the Fusion 360 file so anyone can change it...

... it prints so I made this to fit my printers 2020 frame. ...Its a simple harbor freight soft copper brush that I cut to make it fit inside of the holder.Its a static fit. ...have used it for like 6 months now with out issues at all on my 400mm bed.

I modified an existing Fluke Meter Holder design to accommodate my Harbor Freight Multimeter. I did some trimming and resizing in Tinkercad and came up with a stand for my meter that sits on my bench and holds the meter making it easier to use and...

Organize your Harbor Freight clamps. 4, 6, or 8 clamp holder (6 should be short enough to print on most printer beds) The clamps are designed so that the clamps are angle to the left (insert clamps from the left) because I'm left-handed. You will...

Make sure you log and pay attention to the disassembly process of your torch. To get started, lift the sticker carefully that is at the top of the housing. you may also consider swapping the spring in the switch or adjusting the tension by...

This is an easy mount for wall mounting disposable gloves from Harbor Freight. I used a level to draw a baseline, then measured the box and drew another line with a level to keep it square while mounting. quick, easy, functional!!! These...

This is designed for those cheap flash lights from harbor freight but will probably work with many other brands. the holes are 28mm diameter. One design has 4mm holes for mounting with screws and the other does not for mounting with tape. I printed...

... items. ...I don't remember what the print settings were but it was printed in PLA Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 200 Infill: 20 Filament: Tianse PLA Yellow Category: Tool Holders & Boxes

Harbor Freight Pittsburgh 8 Piece Pin Punch holder for 2 sets of punches.

This holder was designed to hold Harbor Freight/Central-Forge part number P4614, 12 piece needle files with poly handles.

Upright organizer and holder for your Harbor Freight Allen wrenches Great in a workshop or makerspace for quick access

Made a pick holder to hold my pick set I purchased from Harbor Freight, it will hold 9 picks.

This is a bit holder for the Harbor Freight socket hex bit 9 piece set. ...Very handy for my workbench .

Probe holder for the cheapest multi-meter harbor freight carries. ...I've seen this model at other stores just with a different label slapped on, so it should work for those as well.

This is a drill bit holder for the harbor freight drill bit set with 1/4" hex drive. It can hold any 1/4" drive bits or tools, up to thirteen (13). I use slic3r for my slicer. ... Enjoy.

I bought an 8-piece pin-punch set from Harbor Freight sever years ago, I finally to tired of them getting loose in my toolbox so I drew up a quick and dirty holder for them. The pin-punches fit nice and snug in the holder as designed. ... ...

A simple holder for the basic Harbor Freight forstner bit set. For mounting, I drilled two holes in the back and screwed it to the edge of a shelf. ... It's not beautiful or incredibly innovative, but it's super handy and fixes the fact that the set...

A wall mounted holder for the Harbor Freight Punch Set: https://www.harborfreight.com/8-piece-punch-set-93424.html I smeared some black silicone in the recess then wiped it off the surface. ... Nice contrast and easy to apply and wipe.

A wall mounted holder for the Harbor Freight Punch Set: https://www.harborfreight.com/8-piece-punch-set-93424.html I smeared some black silicone in the recess then wiped it off the surface. ...Nice contrast and easy to apply and wipe.</p> Category:...

This is a remake of Disposable Glove Holder by mkelly I was looking for a holder for my glovebox from harbor freight when I came across the Disposable glove holds which mount the bok vertically and I needed to mount sideways horizontally, So decided...

Tool holder for 9 piece 3/8" & 1/2" drive hex socket set from Harbor Freight. Fits this product: https://www.harborfreight.com/9-piece-38-and-12-drive-metric-hex-bit-socket-set-67880.html Counter bored holes in the bottom are for 3/8" X 1/8"...

I wanted a more portable way to use my harbor freight Twrenches so I designed this in Fusion 360. ...I painted the top of mine so I could see the sizes better.