hard drive rail 3d models

Here's how it works: I redesigned the Hard Drive Rail and encountered some problems, particularly within the hollow interior and issues using a screw as there is no space for the screw head to engage. ...I referenced these dimensions to create this...

This allows you to mount an additional 3.5" hard drive in your Corsair 4000D on the surface above the power supply using readily available tool-less hard drive rails (make sure you still have adequate airflow and cooling). It can also be used to...

I haven't printed these out yet, but they'll fit perfectly when I get around to it.

The item is a thin rail designed to connect with a typical 3.5" hard drive for installation within a tower computer. For years, I owned an unused hard drive because I lacked the necessary rails. Visiting local stores proved unhelpful and online...

My Lenovo Thinkpad T420 came with a 7mm drive for an SSD and appropriate rubber rails, but I wanted to fit a 9.5mm drive in. This solves that. I guess this would be most like the original if you printed in TPU, but I printed in PLA+. I think the...

My Lenovo Thinkpad T420 came with a 7mm drive and appropriate rubber rails, but I wanted to fit a 9.5mm drive in. ...This solves that.</p><p>I guess this would be most like the original if you printed in TPU, but I printed in PLA+.</p><p>I think the...

After scaling to compensate didn't help and not caring about it being tool less, I just changed the pins to counter bores located on the original pins.Added a second set of mounting points for 2.5 inch drive adapters.Without the pins it may be...

HHD Rails.

reversed 3.5" hard drive rails from VisionKJ

No additional hardware is needed; simply press-fit the pegs into the screw holes of standard 3.5" hard drives or 2.5"-to-3.5" adapter caddies, then slide them into the hard drive rack. To print these rails, orient one of the narrow sides to the bed...

... does not need to be mirrored for left and right. I used a bit of supports on the 2 stubs and non on the latch. 120mm rail height If you need to edit: https://www.tinkercad.com/things/0HSJH777Kfq?sharecode=M2nFCMfub2HwEl700iC9bb-M82nHG8sCBhwpRx8sVLM

I was still experiencing issues with shrinkage, despite having calibrated the printer. The problem persisted as the pins on the original part continued to pull closer together. Scaling my design failed to yield any improvements, so I decided to...

Remix of 3.5" Hard Drive Rail 12.5mm by 155mm By FirstDue3D modify with holes to screw into hard drives.

To install a Lenovo C20 computer hard drive, I created slide-in mounting rails using Solidworks, as no aftermarket brackets were available. My rails differ from the original by utilizing two 6-32 flat head screws per rail for secure attachment. ...The...

I needed some generic plastic drive rails that fit the standard 3.5-inch hard drive. They are ridiculously easy to find online, and they work amazingly well - I'm really pleased! ... **Printing Details** PLA Filament: 0.3mm layer height | Printing...

This is an universal 3.5' hard drive rail for PC cases. It is made as short as possible to fit 10x10x10 3d printers (crosswise). ... Size is: 4mm x 12mm x 113,6mm Screw holes are 101,6mm apart.

I upgraded my Antec Solution SLK Series Computer Case with custom hard drive rails, giving new life to an otherwise discarded SLK3700-BQE model that I had inherited. The case still had plenty of usable parts, but was missing some essential...

I hastily constructed these rails to accommodate the hard drives in my ix4-200d iomega StorCenter NAS, which I acquired as a gift, although it lacked the HD holders that normally come with it. ...These makeshift supports aren't an exact match to the...

If you ever need to remove the hard drive, you can just use the printed rails to pull it out. Or, better yet, just tug on the hard drive itself and it comes right out. Needless to say, these will not lock the hard drive inside the server... So if...

It's quite annoying when you try to install another hard drive but notice you either lost the extra drive rails, or if you acquire a computer from someone else who threw away the extra drive rails. Well, here goes. Here is a printable 3D model...

... sell them without RMAing the whole unit, which wasn't going to happen. You'll need 4 x #6-32 countersink screws to attach this rail assembly to the hard drive. ... I recommend printing this design with a 0.1mm layer height with 100% infill.

It securely holds one 3.5-inch hard drive in place. To ensure perfect symmetry, simply replicate this design for the opposing rail. ...The provided anchors serve a crucial purpose by preventing warping during the printing process; once complete, they...

Dell Laptop Hard Drive Rail Set (Left & Right) 7.0mm Dell Part Number/SKU: 5D56T-N80M Label on part: (EAR-11) Compatible Dell Laptops/Notebooks: - Precision M2800 - Latitude E6430 ATG - Latitude E6430s - Latitude E6540 - Latitude E6330, E6430, E6530...

My Lian Li 'PC V1000 Plus' caddy had custom bolts to attach the hard drives. All now missing in action! I created a more common 'rail type' that locks the drives in. Took about 4 hours to print full replacements with 2 spare on an ender 3. Quite...

Designed these for a friend who has a ibuypower case we did not want to have to buy rails so I designed some. I made a 2.5 and 3.5 size so it should work for both. ...You can print a 0.3 layer height with no supports and it fits great, snaps right in.

Designed these for a friend who has a ibuypower case we did not want to have to buy rails so I designed some. I made a 2.5 and 3.5 size so it should work for both. ...You can print a 0.3 layer height with no supports and it fits great, snaps right...

... print time for one set of two HDD rails is roughly 1.5 hours when printing at a layer height of 0.2mm. Note: I haven't printed the CD/DVD rail myself, as it was modified from an existing HDD rail design and should be generally okay to use.

... two M2 screws to secure the carriage. ...You'll also need 4 hard drive screws that have a tapered (countersink) head (this is a requirement as there are very tight tolerances on either side of the hard drive and there is NO space for screw heads.

Summary: I designed this enclosure for 4x 3.5" hard drives to be mounted and enclosed easily, while also being on rails for easy insertion and removal for maintenance. I have included my original version 1, and my new version 2 with active cooling...

A din clip I remixed from the original so that I hang large amounts of hard drives on a din rail. ...Print it on its side, zero support needed.