hareball shell 3d models

I've combined the six pieces into one STL file, but you can easily separate them in Simplify3D (using Mesh / Separate Connected Surfaces) or Meshmixer (using Edit / Separate Shells) if you want to print each piece a different color. There's a 1 mm...

If you print with two shells and a 0.4mm nozzle, you should be able to comfortably handle vertical angles of 60 degrees. Clip lengths at 60mm, 90mm, 120mm, and 150mm are added to the thing as examples. These all use a clip thickness of 16mm and a...

GPX can be run from the command line, called by shell scripts or run as a post process. It has built-in support for 5D Cupcake, Thing-O-Matic and Replicator 1/2/2X printers. GPX can also load custom machine definitions if required. ...GPX configuration...

This block works best when printed with a 25% infill, three shells, three upper layers, and three bottom layers. **Assembly Instructions** 1. Mount the 608ZZ bearing onto the axle. 2. Insert the axle into the slot in the upper block. 3. Attach the...

... Notes: Printed mine using supports set to touching build plate settings. Settings were: Layer Height - .2mm Shell Thickness - .8mm Top/Bottom Thickness - 1.05mm Infill - 50% Print Speed - 40mm/sec Support - Touching Buildplate Brim - 10 lines

Required parts: 1x Body.stl (beware of bottom, one side has removable supports in the eye and in the ball bearing seating) 4x Washer.stl (keep distance between wheels and duck's body) 2x Wheel_B.stl 2x Wheel_B_mirrored.stl OR: 1x Body.stl (beware of...

To prevent the shell components from shifting off the print platform, use a brim on FDM printers. Depending on your specific machine, printing settings will vary greatly. This model was created based on community feedback. If you'd like to suggest...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 1 Rafts: Not Necessary Supports: Yes Resolution: 0.27mm Infill: 0% Notes: Print with exterior support, 0% infill and 0 shells for optimal results. Larger sizes may require 5%...

... a body length of 'supporting friends' under this baby! Make sure to leave at least 2mm of shell during printing to reduce wobbles and quakes! ... After Print Take some extra time to ream those holes - with any luck, you'll be smooth sailing.

... where you want to have the base at zero, i.e., b = 'sub{ 0; }'. If your base function is anything other than a plane, you are probably going to need to print with support. It is possible (but a pain) to use b to print a shell rather than a solid.

I have provided a model of a full 20ga shotgun shell and a Tokarev 9mm bullet for this purpose. These are optional and are not required for anything else. The knurled grips are particularly tricky to print, so I have provided two other versions that...

Important basics include: Top and Bottom Layers = 0 Outline/Perimeter Shells = 1 Retraction Vertical Lift = 1-2 mm (very important to lift the blade when crossing open areas) No skirts or brims One print/cutting layer is recommended, with a layer...

Printed with CURA 15.04.6 shell thickness 5mm bottom/top thickness 1mm I use a 0.5mm steel nozzle with 0.25mm layers to print with FormFutura CarbonFil at 50mm/s It's a difficult material since it doesn't stick well without a heatbed and you really...

https://creativecommons.org/licenses/by/4.0/ "Head" Shell: https://www.thingiverse.com/thing:4151150 by grandYann Licensed under the Creative Commons - Attribution - Non-Commercial license. https://creativecommons.org/licenses/by-nc/4.0/ Weapons...

Print Settings Printer: FlashForge Dreamer Rafts: No Supports: No Resolution: 0.15mm Infill: 75% Notes: Use 4 bottom layers, 6 top layers, and 3 perimeter shells. On FDM-printers it is highly recommended to print the lock in the attached two parts...

Machine parameters for Cura 2.1.2 were set as follows: Layer height: 0.2mm Shell thickness: 0.8mm Infill density: 35% Speed: 25mm/sec Temperature: 210°C Flow rate: 110% For those using a TinyBoy with Cura 2.1.2, my settings can be found on GitHub. ...A...

For those who want to shave every gram off their printing head in order to fight ringing, or simply want some new stylish grilles to give their printer a makeover, here is a compact and low-noise replacement for the popular iron fan grilles.\nIf you...

Printer Settings: Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Yes Supports: No Resolution: 0.20mm / Standard Infill: 2 Shells / 20% infill recommended Notes: Recommend using Raft for ease of removal from the build plate. DO NOT USE...

Components required total only a quantity one thusly list all parts specified accordingly below the part needed for construction is described with specifications clearly indicated also be sure that when constructing each part specific attention...

## Original Design My original design (ncq-display-unit-no-back-plate,stl) is a hollow shell, under which, LEDs can be wired and powered. There is no base plate, giving access to the underside. ## Updated Design The updated design...

If you want to use both the Filament Out sensor (GPIO-0) and Filament Jam Sensor (GPI-2), then the solution is to use Raspberry shell script to detect the filament jam condition and turn off the printer when it occurs. The script...

I began with hempstick's excellent shell model and going from there I've been adding electronics and a base. After that's done, who knows? I think perhaps an F-18 stick/throttle will be in order but I'm open to suggestions. I'm on the HOTAS Discord...

... down each model with fine emery and then subject it to an acetone vapor bath for 60 seconds when using FDM printing. This seals the shells and creates a smoother appearance but removes some of the detail - hence, I build more detail into the model!

This can be done by changing the model to have zero infill and zero top, bottom and side shells, then adding a box modifier that restores these settings and placing that modifier just on what you want to print.Now print both hemispheres, and print...

After the battle, this Phoenix was rebirthed, and as a token of gratitude, portions of its egg's shell were given to the leaders of each of the seven tharchs that had responded in aid. The shell pieces possessed some latent power related to fire. It...

(very few supports are needed, should only need them at the base) PLA, on makerwares Standard profile: 10% infill, 2 shells, 0.20mm, 230º, 90mm/s extrusion.I have also printed a stronger version by using 20% infill and 2-3 shells.I have also...

You want one perimiter shell with a tiny bit of squigly filament in between shells * The OpenSCAD file is attached for anyone who wants to dive in. I've also enabled the customizer but this is my first attempt at that, so your mileage may vary. ...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 1 Rafts: No Supports: No Resolution: .2 Infill: 15% Notes: Printed with 2 shells. At above print setting, mass of the Gamma - Insert was about 6.7 grams using Toy Builder Labs Black...

Careful with the small parts, don't overtighten or they'll break.Print SettingsPrinter Brand:FlashForgePrinter: Creator ProRafts:NoSupports: YesResolution:The three small parts (Bolts, Capnuts, Spacers) should be .1 mm, the rest can be an...

OBSOLETE For both gears and nut retainer, I used PLA and these slicing values: .2 layer height 80% infill 1 shell/perimeter 3 top and 3 bottom shell The body, idler and strut uses similar values but with 20% infill instead. Tools I used: ...