harness 3d model

A front Cable guide for the Jubilee printer. Requires (2) M5X10mm button heads. This is designed to print as shown without supports. ... If printed sideways threads will not print well.

When printing in ABS, I struggled with keeping Big-E's original design intact due to warping and detachment from the bed. To solve this issue, I modified it by adding mouse ears that significantly enhanced adhesion. The result was a flat finished...

The motor wires that connect the X-axis bracket to the Y-axis bracket need to stay elevated from the workspace and off the gantry as the tool navigates across the beam. Keeping these two components upright keeps the wires organized, providing an...

VERY much a work in progress. ... I will probably start over at least one more time, but so far I like where this one is going

The lifting lid of the MMU compatible prusa enclosure (https://blog.prusaprinters.org/mmu2s-printer-enclosure/) becomes very back heavy when five of my dryboxes (https://www.thingiverse.com/thing:3867357) are on top. While servicing the printer I...

This is a strap holder for the DJI RC Plus remote controller Print Settings Printer brand: Ultimaker Printer: S5 Rafts: Doesn't Matter Supports: Yes Resolution: 0,2mm Infill: 20% Filament brand: RS Pro Filament...

For the hotend cables I used a big Self-Closing Cable Sleeve Cover Cable Management. I first drew the piece, then printed it and used it to drill the two 2.5 mm holes on the back plate of the MS NG and finally tap 3mm, which leaves the first...

Customized version of https://www.thingiverse.com/thing:2127368 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2127368

This is a quick and dirty tool I built to get some thrust measurements off of my t-motors.

This is a Custom Mount for M3d's Crane Quad's Heads Wires, designed specifically for attachment along the Back of the X Axis. At the request of a user in the M3D's Quad Owners Community on Facebook, I created this alternative solution. The...

Customized version of https://www.thingiverse.com/thing:2127368 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2127368

Customized version of https://www.thingiverse.com/thing:2127368 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2127368

I'm excited to try spinning this text for you. Here is the rewritten text: "Enhance airflow in your MetalFish S3 Plus ITX case with a custom fan frame. ...Swap out one 120mm fan for two powerful 92mm fans, boosting airflow by up to 60% while...

Yet another wingfoil hook. I used this one for long https://www.thingiverse.com/thing:5425008 but I had some issued with the newer corength decathlon belt. Now with this new remixed design, the hook stays in place even if the wing is pulling very...

I'm planning to replace my hot end over the weekend, but what really got my attention was how much I dislike running wires. To solve this problem, I designed a block that features four 2-pin terminals. My goal is to connect my hot end and two fans to...

Designed to use with Micro Swiss Direct Drive Base for Ender 5. As a bonus - now it is so easy to operate extruder's spring arm. Screwed to the base using 2x m3x12 screws Needed to attach a 3/4 inch [split wire loom...

Made some new mounts for the Printer mods direct drive kit for the Ender 3. The original mounts would kink the extruder cables, you might need an other 3mm x 50mm shcs bolt for the extruder mount, I only put one in because the bracket was tight and...

The lifting lid of my Prusa MMU compatible printer becomes extremely heavy when five dryboxes are placed on top. While servicing the printer, I accidentally pushed the lid too high and it flipped all the way back, causing damage to the hinges and...

Customized version of https://www.thingiverse.com/thing:2127368 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2127368

Customized version of https://www.thingiverse.com/thing:2127368 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2127368

This is a quick and dirty tool I built to get some thrust measurements off of my t-motors.

Solve Printing Issues by Redirecting Wires with Customizable Z-Axis Maximizer. A Remastered Version of http://www.thingiverse.com/thing:620627 Enhances Compatibility with http://www.thingiverse.com/thing:507944. Easy Setup Instructions: Print the...

Individuals harness the potent rendering prowess of 3D modeling behemoths like 3ds Max 2015 when augmented by VRay's cutting-edge abilities, effectively producing photorealistic images from files stored in proprietary formats such as .max, .vraymax,...

Rigged 3D model. ...Easy to use for animation and games! High-quality 3D model, Sculptured in Blender. ...3D printable.

A 3D model that can be used as a decoration

In 3DS Max, a 3D model fails to render its texture correctly.

its 3d model which contains wireframe,psd,obj,stl,png files

A 3D-modeled piece of jewelry, in the form of a square pendant, awaits your selection.

I added different connectors to each harness and created a connector-to-connector connection between Harness A and Harness B. Additionally, I incorporated electrical protection covers in the form of corrugated tubes to safeguard the wires. ...Catalogs...