harry styles tree topper 3d models

<h4>Height</h4> Measuring 220 millimeters tall. <h4>Bottom Hole Diameter</h4> Compressing to a diameter of just 18 millimeters at the bottom. ... <h4>Software Development</h4> Carefully crafted in Cinema 4D using Loft Nurbs technology.

I replaced the hooty face with this one https://www.thingiverse.com/thing:4744918 and scaled it to fit nicely then sliced it into more easily printable parts, optimised to only need supports on the house section

Merry Xmas Everybody

Enjoy the magic of Christmascheck my patreon page and if you like it maybe you want to support me and my work. ...Thank youhttps://www.patreon.com/DonCipriano3D

A Volkswagen inspired Christmas star.

Made from 2 pieces to be mounted together with an M3 Screw. Spray paint glitter ... it's up to you. Hope you enjoy this design. ...My other thoughts ....need to make it lighter in future.

This creation was designed using Tinkercad's intuitive tools and features.

Scale the Z-axis uniformly to achieve your desired height.

Merry Xmas Everybody

I really liked this basic design but wanted to be able to print it in two sections, needed to hollow out the base, and insert alignment holes for the parts. I used Blender to make these modifications. The holes are designed to accept a small piece of...

i hope you like it! ...

The star is splitted in 2 parts that need to be glued/fused together.The base can be printed without support.

I printed this on a Prusa Mk3s. Layer height .2 You may or may not need supports depending on your machine. Print twice, and them glue or tape seams. I used a 16 LED neopixel ring to light from the inside. Lights are controlled via an adafruit...

Update 4 Now a staggering 53.42% more festive than previously mentioned offerings. Observe as this majestic being bears gifts, perhaps even death itself. Update 3 Exhibiting noticeable flair! Update 2 Unleashing unwavering festivity! Update 1...

It prints well on a Prusa 220x200 when you rotate it on the bed 45 degrees. ... The OpenSCAD design was build from scratch by me.

This unit measures 1.9 times its original size, boasting a prominent star at the center. Its sturdy peg measures 15mm in length, 5.25mm in width, and 6mm in height. ...The entire structure reaches an impressive 106mm in height.

In your slicer set up the initial bottom layer to 0, infill 0% and the wall line count to 2. Recommended to use brim with at least 10 line count for a better adhesion. ... I used white PLA and I put the christmas lights under it.

I designed this to allow for putting a medium size bulb (mine is 27mm at the widest) inside to light up the star. You could also add the bottom point, just be aware that the bottom hole is slightly larger than all the others. I originally tried...

Enjoy! ...Will need to enable supports for the the face.

My wife wanted a start that fit in with the theme of the stars you see below:Designed to fit this light:https://www.amazon.com/Accessory-Cord-One-Light-Bulb/dp/B07W726LD5?th=1The base should print nicely without support but the insert will need them...

Print 2x and glued together

Remix of http://www.thingiverse.com/thing:1284637, basically just hollowed out using Fusion 360 with precision and care. I plan to drill small holes to allow light to pass through, ensuring they are tiny enough not to be modelled. I'll also drill...

I created my own basic star model with clean flat faces since I couldn't find one already available. To achieve optimal results, I suggest printing the design upright and omitting bottom layers entirely - this is essential for creating a hole in the...

Create a festive decoration using RGB self-changing LEDs by cutting parts from a 5mm acrylic sheet using a dxf file and a laser cutter. Assemble the star with five M3x20mm screws and mount it with two M3x16mm screws. Sand the top layer with 80 grit...

<p>I couldn't find a basic star with clean flat faces so I modeled one for myself. I recommend printing it upright with zero bottom layers (to make the hole) and supports for the bottom edges of the spokes on the star. I attached an image of the...

Remixed to use the tabs added by Captain4W for glue up surfaces but removed the bottom tab and the center support to make room for an LED light strip. I also scaled up the Inner Star to 120%. Need to print (2x) "InsideStar" and (2x) "Outside Star". I...

I give all credit to gshorts for the original design. I utilized netfabb to reorient the objects for simpler printing. If I were to print another one of these in the future without a looming Christmas deadline, I might opt for a finer print...