hayward to intex adapter 3d models

A versatile upgrade kit designed to effortlessly integrate a standard 2-millimeter electric motor into even the most cramped spaces, including those typically limited to accommodating only a 5-millimeter diameter shaft opening.

Simple slimline mount to mount an 80mm fan to a 92mm fan case. Most 92mm mounts have a spot for 80mm fan screws but my case didn't so I made this. ... Shouldn't need any supports.

I made this to be able to put my led ring light on a tripod. ...It is an Arca style plate with a 12 mm light stand rod on the other end.

To securely mount an iPhone 5 on a Gorillapod, print a custom-designed holder that supports overhanging features. ...The printed holder perfectly accommodates the device without slipping and easily attaches to the tripod leg for optimal stability.

Designed this adaptor to connect my shopVac to one of those amazon dust collector. ...Printed it at full scale with a brim and no support and got a nice snug fit .

This revised version empowers users to disconnect and manage the 5015 fan independently, offering flexibility in certain scenarios.

This design simplifies attaching BLTouch mounts to inductive sensors, offering compatibility with both 12mm and 18mm variants.

Hi there, this is a frame to put two SSDs into a single DVD slot of a pc.

I remixed danielroibert's remix to print vertically. ... * removed positive symbol and saved model in vertical position.

An SMA female-to-female connector, specifically the Tessco part number 34013, is what this product represents.

This tool allows you to use the available Gopro (tm) mounts together with your DriftHD (tm) camera.

The model should be printed in vase mode.Only 2.4gr / 0.79m of PETG is required to print it.

Shipping was too slow so I had to print it myself faucet: 25cm outer diameter pvc: 16mm inner diameter

PLASTIC MATERIAL IS LIMITED TO ACRYLONITRILE-BUTADIENE-STYRENE ONLY. ...3D PRINTER SPECIFIED IS A PRUSA i3 MODEL.

A versatile attachment designed to seamlessly integrate the selfie stick's phone cradle with a wide range of GoPro accessories.

This device attaches firmly to one end of a BluTrack and enables seamless connection of multiple Hot Wheels tracks together.

I specifically designed this project to utilize a 60mm fan on a standard 40mm fan duct, and I'm pleased to report that it functions flawlessly. If you're looking for an even more compact solution, feel free to print this design by scaling the z-axis...

Non intrusive and discrete base for Somfy wind sensor to be mounted on Lindab rainwater pipes. ... Pipe diameter: 90 cm.

... a bit. You may need the +1 mm pin also. Print in 0.1 layer hight and 100% infill. Print it hot and slow to get maximum layer adhesion. Use support (I used tree suport). I also set "Horizontal Expansion" to -0.3 in Cura to make it easy fit.

To install a larger fan, such as a 50mm model, rather than using a standard 40mm unit.

One fits 11x5x4 bearing, and one fit 10x5x4 bearing. ...If you need other size, feel free to contact me :-)

this design requiers you to remove the mount part off the included rubber band handle bar mount for niterider lights

Needed to connect my shopvac to my harbor freight belt sander and needed a coupler so I made this quickly in F360. It looks a little off however I wanted to print it with no supports. ... Large opening is 58mm and the other end is 45mm.

... as I remixed this within PrusaSlicer and Thingiverse doesn't allow 3MF on it's own. Remixed to convert CR2 3V lithium batteries to CR123(A) 3V size. Requires wire or tinfoil to bridge the negative at the bottom as per the original design. ...

I recently purchased a replacement dusk-to-dawn control switch for my converted gas-light to low-voltage outdoor light assembly. The original photocell light switch model had a significantly larger eye pattern, making the new design stand out...

Created this for my niece's wooden train set. ...Not entirely sure of the brand as it appears to be a generic copy, so your mileage may vary. Intended to stand on a single stud Duplo block, but can accommodate a stud to each side of the track as well.

Just wanted to be able to use 2 4010 blowers instead of a 5015 blower to see the print difference with some of the 5015 based part ducts for the ender 3 v3 se.It fits in model. ...https://www.thingiverse.com/thing:6428435Created a 2nd model with it...

... on a prototype board.Simply use copper wires from a phone line (or RJ45 cable). Apply some tin to both the wires and the ATTiny. Insert all the wires as shown in the picture, then place the chip and solder everything.Ensure to check the connections.

This is to convert a mini with a 25mm base to one with a 50mm base.  If a character is enlarged, you can use this base. ... Also, if you don't want to print large minis, you can make medium sized ones and use this base as well.

... which can be found here: http://www.thingiverse.com/thing:780379. ... Print Settings: Rafts: Yes Supports: Doesn't Matter Notes: I printed it with one raft layer at zero contact distance to keep it attached, making it easy to cut or rip off later.