hayward to intex adapter 3d models

... everything over to Netfabb, cut it in half, and voila! Next, I attached the GoPro mount to the VEX mount with some glue and off we go! It might be necessary to shave off about 0.1mm from the bottom since the large piece has a thin lip on it.

This guy will allow you to connect a hose with male GHT (aka 1 1/16-11.5) threads to the 55/64 (aka M22-1) threads on a male kitchen faucet. ... In our case, this was needed to connect a male Gardena quick-release connector for a portable dishwasher

Made to convert a coupling from 8mm to 3mm. - Mini CNC bit. Stretch to 8.1mm XY, 100% infill, brim adhesion. --- I just used this photo for reference. A spring coupler should never be used under high speeds like for a spindle. Photos for reference...

... on phone size and if you want to mount vertically or horizontally. ...The length refers to the distance from the center of the quad lock to the bottom of the tripod mount. ...Let me know if you need a different length and I will upload it for you.

Bought two Noctua fans to replace part cooling and board cooling fans, but started haing jaming problems because of heat creep due to the lower airflow of Noctua fans. ... Designed this duct to have both fans cooling the board so it doesnt fry xD Works...

... show how to convert a regular AA battery into a C-sized one, suitable for use with penlights. ...Simple modifications are required, such as adding slants to the battery for secure fitting and increasing its diameter, if needed, to ensure a proper fit.

I'm planning to swap out the CPU fan holders in my Jubeat PC setup with some 60mm Noctua fans. ...To create a sturdy base, I'll print this part with a whopping 99,999 bottom layers and 100% infill - that's what it takes to make something solid!

The mainboard's power supply fan suddenly stopped spinning, revealing it was a rare 135mm model that proved difficult to locate and pricey to replace. ...In response, this modification aims to repurpose a readily available 140mm fan as a direct...

... insufficient friction causing filament tangling. To rectify this issue, install these new spool holders, which offer optimal friction to prevent unwinding. ...Retain and reuse the existing screws and nuts from the original holders for installation.

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=673563 Options Used: Motor Axle Diameter Set to 2.3 Centimeters Coupler Length Set to 15.9 Centimeters Coupler Outside Diameter Set to 7.2 Centimeters Try Bigger Sizes Option Disabled

This is to convert a mini with a 25mm base to one with a 50mm base.  If a character is enlarged, you can use this base. ... Also, if you don't want to print large minis, you can make medium sized ones and use this base as well.

I purchased a versatile accessory that allows my GoPro camera to securely attach to any object using its Joby Gorillapod Ballhead mounting system. The unit consists of a sturdy clip with an adjustable clamp and a rotating ball joint that enables...

... file is provided, there's a good chance it won't perfectly match your specific phone and binoculars/telescope setup. Download the OpenSCAD file and make any necessary adjustments to the (thoroughly documented) parameters to suit your unique needs.

... instructions to the letter. You'll also need two screws - I used M3x3.5s that came with my SSD - to secure the drive to the bracket. ... Instructions: https://www.ifixit.com/Guide/iMac+Intel+27-Inch+Retina+5K+Display+Hard+Drive+Replacement/30522

... design. The V8 version features fillets on the sides, which are designed to prevent damage to the rubber on your respirator and is slightly taller than the V4. ...This design change also helps to avoid interference with 7500 half-face respirators.

It's working perfectly without any need to adjust chain tension, making it a great option compared to most projects available here. Tested thoroughly, it works flawlessly every time. Simply adjust the dimensions to suit your specific needs. Before...

If your camera has a backfocus of 17.5mm you don't need any other extension.To reach the working distance of 55mm, wich is perfect for mst coma correctors, you need an additional 5mm M42 extension. This is because in my case the printed M42 male...

When combined with pins, a level shifter to convert 1.2v logic to 5v, and an Arduino or other Atmel processor, you can connect your digital calipers to just about any device. I'm working on a software toolkit that will make this possible. One of...

Fischertechnik Gear Motor to Lego Axle Fischertechnik_Gear_Motor_To_Lego_Axle Fischertechnik_Gear_Motor_To_Lego_Axle_2 Additionally, the Fischertechnik encoder gear motor can be printed onto a Lego axle. Fischertechnik_Encoder_Motor_To_Lego_Axle...

One thing to note is that gravitrax and lego are completely different alignment and you can not use a lego baseplate to align your gravitrax hexagons, they will have a gap between them. ...So, this is only a way to place a gravitrax piece onto a lego...

To make it easier for the 18650 to protrude out, I lowered its height to 60mm. Also, the sleeve's internal diameter was reduced to 20mm. However, surprisingly, an 18mm battery doesn't fit in an 18mm tube. This design's interior diameter has been...

I used this model for my DIY servo project: https://projectstem.co.uk/2019/08/21/diy-servo-sort-of/ Components Used: Motor: Order from Banggood at https://www.banggood.com/custlink/vKDK8NrDi2 or on Amazon at https://amzn.to/2NotZSC H-Bridge: Buy from...

I successfully utilized a duplicator i3's settings to create this print, however the .4 nozzle height limited its thickness. To compensate, I manually drilled out the interior using a drill bit until it snugly fitted. If anyone is experiencing...

... optimize print speed. Resolution is set at 0.1mm, ideal for detailed prints. Infill density is adjusted to 50%, striking a balance between strength and weight. ... Designing This Project I designed this project using libreCAD and openSCAD software.

When you've got a monitor that fits snugly into a 75x75 VESA mount, but your wall bracket is designed for a larger 100x100 VESA screen size, you're going to need something special.\r\n\r\nUnfortunately, I'm no longer able to verify the exact screw...

Fusion360 file contains 2 parameters that you can change to adjust it to your shaft and bit dimensions.It is a part of a 3D printed electric screwdriver project that will be published here soonI didn't try to print it without supports, printing it...

All you need to do is attach the supplied metal part to your 31.75 mm, 32 mm or 1.25" telescope eyepiece and you're ready to go. ...The design was inspired by a popular project on Thingiverse, but this one is specifically tailored for Samsung NX users.

To confirm accuracy before printing, verify the dimensions as my model slightly deviates due to calibration issues with my printer. ...Print only the initial layer and carefully measure the distance between the holes, which must be precisely 75 mm...

... ... I'm also adding freeCAD project in case anyone needs to adjust anything, just be carefull as thickness modifier is really picky and can suddenly stop working, solution would be to use additive pipe but for whatever reason that's not working for me

This model was made so that the strap accessory of Quest 2 can be used on Quest 3.https://youtu.be/BGd2rGTc6MkIt was manufactured with the length in mind so that the power cable can be safely connected to products such as battery straps.It is also...