heated bed 300x300 3d models

These clips attach to the heated bed and slightly overlap the glass. The glass I use is 8x8 inches and about 2.5mm thick. There are short and long versions of the clips. I am using four short ones and two long ones. (Later note: I only used these...

Had a problem of the Z probe snagging the heated bed cable and causing my belt to slip as it tried to pull out its own wires when traveling near the edge of the glass. So this was my solution to my problem, this was also my very first thing I created...

A printed clamp for holding the glass on your heated bed. The .scad file is parameterized so feel free to modify and do whatever you feel with this.Update:  This doesn't really work well, particularly not in PLA. Considering that a set of 8 bulldog...

I did not like the heated bed options that were out there and created my own that minimized printing volume loss. Just a bit of height is lost for my proto in order to easily bring out wiring. I will be making another proto later that uses a sized...

Movie: http://youtu.be/LktZsegiSIU This is an analog heated bed for an Ultimaker [or every other 3D printer]. No extra hardware and electronics needed. Heated beds allow the user to print without warping the object. PLA doesn't warp that much, but...

I was tired of having to re-solder the wires to my heated bed after them coming loose, and after the 4th time of it, I figured there had to be something better. I found the piece made by Antscran which looked awesome, but didn't quite fit my bed,...

I was tired of having to re-solder the wires to my heated bed after them coming loose, and after the 4th time of it, I figured there had to be something better. I found the piece made by Antscran which looked awesome, but didn't quite fit my bed,...

This is designed to hold an 8 1/2" piece of 1/4" glass in place on top of a Helios Heated Bed (from Panucatt) to get rid of the office clips that take space away from the build platform. It also gets rid of the springs under the bed that can cause...

The hole in the base of the MPMD allows air from the fan to blow onto the heated bed and cool it down. I had originally covered it with a piece of card but wanted something a little better. So keeping with my magnet theme, I designed a magnetic...

Simple parametric clip to attach the glass plate to the heated bed of a Reprap printer. You probably need to customize and tweak this if you want to use it, see the instructions tab. Instructions...

FlashForge printers come with a heated bed (good!) and a scarper tool (good!) made of metal (good!) that is electrically conductive (...) as are the EXPOSED BARE SOLDER contacts (not good) of the 24V bed heater. If the metal tool happens to touch...

Glass bed bolt downs for the Letuoko V3. ...Uses standard M5 bolts.

I created this strain relief bed mount because the wiring for my replacement heater came out the middle of the bed. I also had to make a taller chain mount. This all works with the chain from this model: https://www.thingiverse.com/thing:3151714 I...

I created this strain relief bed mount because the wiring for my replacement heater came out the middle of the bed. I also had to make a taller chain mount. This all works with the chain from this model: https://www.thingiverse.com/thing:3151714 I...

This support is a redesign to extend the area around the bed support further to help limit the amount of swivel the support has.

... ...Made for Diggro Alpha-3, but should fit others of same design. Longer LK4 and LK4 Pro, Alfawise U30, etc. Inspired by a support I found/tried but did not fit my Diggro Alpha-3. Fits above the left rear bed adjuster knob. ... Modeled in DSM.

I created this strain relief bed mount because the wiring for my replacement heater came out the middle of the bed. I also had to make a taller chain mount. ...This all works with the chain from this model: https://www.thingiverse.com/thing:3151714 I...

Adapted from a E12 strain relief design by twhite0101, this bed strain relief collar will make sure the your adimlabs printer runs for years without much trouble. ... All you need is two small screws to put this together.

This model was designed to secure the glass top and heat spreader to the build platform without binder clips. The corner can slide in and out to secure or release the glass top. The design is used in the Artifex 3D Printer...

... fit ordinary LM8UU bearings. But I use the [Igus ones](https://www.amazon.com/gp/product/B071RSDYW4/). Folks with original frames (I'm on Bear) will need some [heat-set](https://www.mcmaster.com/#94180a331/) inserts to avoid clearance issues.

I needed to adjust the build slightly as my glass top was not exactly the same size as my bed. These now fit snug and hold the glass tightly, not sure how long for but I hope a while at least. ...I used Tinkercad for this, my first design, I hope to...

Simple jack for "thin" beds, mine is concave in the middle, with this I can level it. Apply thermal insulation on the "pad" part (cork, neoprene). Insert an M5 nut and its screw on the "jack" part. Use a pair of 8 mm rigid pipes/rods. Place the...

I have built the stack like this (from top to bottom): - Soapstone - Silicone heating element - Aluminum foil (to deflect heat to the right direction) - 3-4mm cork insulation (IKEA Avskild) - 2mm stainless steel plate (can be other material, just...

... maybe put a thin sheet of glass on the aluminium to get rid of the kapton tape... maybe use some oil between the glass en the hot plate to transfer the heat better...Movie: ï»¿cheers\joris www.rooiejoris.nl www.facebook.com/europerminutedesign

One of them being a bow in the pcb heated bed which left a rather large gap between the heater and the glass bed. I also noticed that the bed adjustment screws were threatening to tear out of the pcb. I modified a nice clip that I found on...

Just a little change to make it fit to my 6 mm bed. ... Looks like the Colido has a thicker bed compared to the PrintRite

Bed Handle with Bed Locks that I threw together from a few files in 3D Builder for Ender 3 Max (or any bed with a 300x300 bed size) Here are the original files: https://www.thingiverse.com/thing:4856613 https://www.thingiverse.com/thing:5364491...

Bed Handle with Bed Locks that I threw together from a few files in 3D Builder for JG Maker Artist-D and Ender 3 Max (or any bed with a 300x300 bed size) Here are the original files: https://www.thingiverse.com/thing:3363720...

Soporte mosfet para HotBed. ... Pieza: https://es.aliexpress.com/item/Piezas-de-impresora-3D-controlador-de-calefacci-n-MKS-MOSFET-para-cama-de-calor-m-dulo/32951433029.html?spm=a2g0s.12269583.0.0.effbb5f85sWlnL

Customized version of https://www.thingiverse.com/thing:3468610 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3468610