heltec esp32 lora 3d models

At its core, it utilizes the Bluefly TTL V12 with integrated GPS and barometric sensors from AirWhere/FANET, which relies on an ESP8266 microcontroller paired with a high-range RF LoRa Board. This setup enables real-time location tracking of other...

I installed the LoRaGo PORT – Multi-channel LoRaWAN Gateway on a Raspberry Pi and paired it with an External 900MHz LoRa Antenna and a GPS antenna for added functionality. The combination of the LoRaGo board and the Raspberry Pi can become quite...

* **ESP32-WROOM-32D Cover** - Simple cover that goes over an ESP32 with vents for the SoC and pin holes for the two buttons * **ESP32-WROOM-32D APD-9960 Luminance** - Standard base with cutouts and mount points for the APD-9960 Luminance sensor with...

Remixed the housing from JT https://www.thingiverse.com/thing:2820147 in order to support:ESP32 Feather Huzzah with 2.4" TFT WingBosch BME280 sensorSensirion SPS30 sensor Source code can be found here:...

This is a simple camera mount for ESP32-CAM including USB adapter Printable without supports Access to the RESET button These are the electronics parts I used for my camera...

Battery and ESP32 Holder, designed for these components: AZDelivery ESP32 Dev Kit C V4 NodeMCU: https://amzn.eu/d/6SGyJsc AZDelivery 18650 Battery Expansion Shield V3: https://amzn.eu/d/eqbEHcM You can slide different addons onto the base to allow...

A pair of ‘stands’ to support an ESP32 Maker Kit PCB assembly that can be used to connect to a 38-pin ESP32 module.6mm M2 self-tapping screws are used for attaching the stands to the Maker Kit PCB.More detail on the usage context is available from...

For reference, check out https://www.banggood.com/Wemos-ESP32-OLED-Module-For-Arduino-ESP32-OLED-WiFi-Modules-Bluetooth-Dual-ESP-32-p-1181297.html. It features a sliding top mechanism that may require some finesse to insert, depending on the...

On the ESP32 the "amsreader-firmware" is loaded.The box is designed with YAPP (https://mrwheel-docs.gitbook.io/yappgenerator_en/)Designed for the following boards:ESP32 - Lolin D32; https://a.aliexpress.com/_Ezx6dNTM-BUS - TSS721;...

I'm using mine near the garage to show the status of the garage door using Home Assistant. It might fit a non-Lite ESP32-S3-Box, but I don't have one to test it (plus the non-Lite already comes with a stand anyways).I printed it with 3 perimeters and...

Box for ESP32-S2 equipped with an LD2410C sensor. Printed with PLA, at 0.4mm, no supports. ...DIY Project: https://www.nlion.fr/nicolas-lion-informatique-ancenis/2024/02/25/ld2410c/ Category: DIY

TinyPICO is a compact ESP32 development board that's bursting with extra features, making it an ideal choice for innovators and makers who need a reliable and versatile tool to bring their projects to life.

it's a simple clip for esp32 30 pin. The clip has an island with a hole to be able to anchor it where needed. ...There is one photo that show how I have used it.

The TTGO BTC Ticker ESP32 is available at: https://nl.aliexpress.com/item/TTGO-Nieuwe-BTC-Ticker-ESP32-voor-Arduino-Bron-Bitcoin-Prijs-Ticker-Programma-4-MB-SPI-Flash/32854502767.html?spm=a2g0s.9042311.0.0.27424c4d3gPArG You can find the source code...

Box for ESP32-S2 equipped with an LD2410C sensor.Printed with PLA, at 0.4mm, no supports.DIY Project: https://www.nlion.fr/nicolas-lion-informatique-ancenis/2024/02/25/ld2410c/

Simple case for my ESPresence system - needed a proper case for the Adafruit ESP32 Kit... ... https://www.adafruit.com/product/3269 Print at .03 layer height No need for supports - laying the flat tops on the bed....

This Housing fits a Olimex ESP32-POE and four GX12 connectors. ...I use it as an ArtNet Node for WS2812B LEDs with WLED.</p><p>Screws are 3,0x10.</p>

Multisensor box by www.pihrt.com https://pihrt.com/elektronika/448-esp32-multisnimac-hw1-1-pro-opensprinkler-system OpenSprinkler system https://github.com/martinpihrt/OSPy and https://opensprinkler.cz/

Low profile case for the MH-ET Live ESP32 Devkit board, with a snap-fit lid. ...This case is designed for applications where no pins are used.</p><p>Print at 0.20mm layer height, no support required.</p>

A pic mount for the FX Chrony esp32 display I used a 40mm m3 for the clamp There's room for a micro slide sw and an 1000mah battery

Create Your Own ESP32 Weather Station Build Instructions Get started by heading over to YouTube for a comprehensive parts list and detailed code sketch at https://youtu.be/i9sn_d-Q3Ww.

For some reason my wiring position of the ESP32 board was a bit different so I made a custom back cover case. I also made the lip height longer, just so it fits more firmly. ...

This thing consists of two files. ...A base enclosure and a snap-fit lid. The enclosure has printed standoffs for the ESP32 Camera module and the passive infrared (PIR) sensor.

Here is a rewritten version of the text: "The Eagle XML file for a custom PCB pattern featuring an ESP32 module with a built-in OLED display has been released. ...This package also includes the DIP TRACE PCB pattern library."

This is ESP32 CAM module enclosure which gives your automation project a way better look and also safegaurds it from environmental condition as well as it provides asthetically well display for Automation product.

Remix from ESP32 box and improved balljoints Box: https://www.thingiverse.com/thing:5137983 by thereal-Serenity Balljoints: https://www.thingiverse.com/thing:1668946 by Esquilo ______________________ Printed with supports on the joint side

Snap Fit ESP32 Slim case for those wanting a nice small case when not using any pins on the D1 ESP32. Simple to print with holes for reset and LEDs to shine through. Bluetooth ESP so I added the WIFI/BT logo on top. Enjoy it! Snaps together and...

FireBeetle ESP32 development support. The bracket allows the board to be fixed on a wooden plate or to be mounted in any other device. ... It will require 4 parker screws.

Here is a rewritten version of the text: A three-dimensional model of the TTGO module has been created, featuring an ESP32 microcontroller, a rechargeable 18650 battery, and a vibrant OLED display.

Find More on https://ei23.com/smarthome/awesome-diy-video-doorbell-based-on-an-esp32/ [](https://youtu.be/3w_xTNuditQ "Blinking LEDs")