heltec esp32 lora 3d models
4130 3d models found related to heltec esp32 lora.
thingiverse
This housing fits a Heltec ESP32 OLED Board V3 Type-C SX1262 board without the need to buy screws or glue anything. This case is meant to be used inside or light outside duty.The case was used for a Meshtastic project. *fun fact, you can go to...
thingiverse
Remixed it to print better (Removed button labels) and fit my weird battery.
thingiverse
This is a battery case designed to complement the object found at https://www.thingiverse.com/thing:3783207. To use this case, you must first print out two separate components. If you're planning to utilize a small 1000mAh LiPo battery, printing my...
thingiverse
Made the battery bay a little bit bigger to fit a salvaged iPad battery.
thingiverse
Remixed from: thingiverse.com/thing:4460556 (get buttons there) When I first printed the original, it didn't quite fit the board so I started hacking away in MS 3D Builder until it fit, but the buttons were slightly mis-aligned (probably due to...
cults3d
Made the battery bay a little bit bigger to fit a salvaged iPad battery.
thingiverse
Hardware used: - LILYGO TTGO ESP32 LoRa v1.0 board (can be possibly modified for other models) - Short shaft rotary encoder (15mm plum handle) - Two panel mount push buttons (one is for the selection, the other is to replace the internal button)...
myminifactory
For TTGO T-Beam V1.1 ESP32 LORA with GPS NEO-M8N Case Using Button Head Allen Key M3 x 8mm bolts for Case and Allen Key M2 x 5mm bolts for PCB (need 4 of each Bolts) the PLA or PETG will grab on to the thread of the bolts to secure the pcb and case...
thingiverse
This is a REMIX of TTGO Lora ESP32 V2.1 1.6 - Robust case by JesAde (https://www.thingiverse.com/thing:4518757) Modification: i. ttgo_2.1_1.6- widened bottom.stl : In order to accomodate a bigger/thicker battery, the bottom was widened and battery...
thingiverse
This is a case is made to hold a "LILYGO TTGO ESP32 LORA OLED v1.0" developer module alongside with a rotary encoder. A case also provides place for a 18650 battery, a power switch and a buzzer. One handed operation is possible. The idea behind...
thingiverse
American Human: 3-gram lightweight enclosure for iNAV radar from Oliviver C, available online at a popular RC forum https://www.rcgroups.com/forums/showthread.php?4189550-iNav-Radar-Lightweight-Version/page20#post41902809
thingiverse
Printed with supports on the 'bottom' part 4 pin JST- ZH connector compatible https://www.ebay.co.uk/itm/283986512811 Thanks to another user uploading an STL for a case, I reused their very clever buttons ...
thingiverse
I create my own model since admiral99 is not available right now. ...The current design of this enclosure requires significant improvements.
thingiverse
Tight and precise model, you'll likely require some extra refinement to reach optimal quality. ...Vertical gaps must be filled to ensure proper printing, then carefully trimmed out for a flawless finish.
thingiverse
This is a version of Tinderbox with box and software modified to use Heltec's ESP32 Module with integrated OLED display and battery management. It all works off of a single Lithium Ion cell. For battery power I needed to add a switch for on and off (...
thingiverse
I slightly modified the great original design to fit the 10cm antenna cable better to the enclosure.
grabcad
ESP32-WROOM-32 is a powerful, generic Wi-Fi+BT+BLE MCU module. At the core of this module is the ESP32-D0WDQ6 chip. ...The embedded chip is designed to be scalable and adaptive.
thingiverse
ESP32 Detailed Model for Reference. ... This detailed model showcases a customized NodeMCU ESP32S design, serving as a precise guide for crafting a tailored housing solution. ... Dimensions: - Length: 49.5 mm (includes USB port) - Width: 25.9 mm
thingiverse
The primary electronics are housed in an Heltec LoRa ESP32 board and a Hall Effect sensor. For a complete parts list, click here. ... The software, documentation, and schematics can be accessed on my GitHub page:...