heltec 3d models
198 3d models found related to heltec.
thingiverse
These mounting tabs for 1.3" OLED displays, such as Heltec models found on eBay, are disposable units that insert between the display and main PCB. They're secured with a hot solder iron, riveting them in place. Custom STL models call for two 3mm...
prusaprinters
The threads don't require supports, but I add one in the middle of the dome where the angle of the curve reaches 65%.The original Heltec variant shown in this listing can be purchased here: https://www.etsy.com/listing/1315161160/Thanks for your...
thingiverse
####################################################################### CO2 Ampel / Meter (neues Gehäuse, 2-2021) In dem Gerät steckt ein Heltec LoRa WiFi v2 oder ein NodeMCUv2 Amica als Mikrocontroller, kombiniert mit einem Bluedot BME680...
prusaprinters
Darknet-NG 13 Badge Version 1.8.1 I spent a few hours updating the body of the badge with ya'll input.Badge Body, reinforce Badge Face Lip Badge Body Add spacer to hold the Heltec board in place when plugging in USB without blocking the...
prusaprinters
Especially for the use of the current Heltec Wifi V3 controller, the pin assignments are explained under the following...
thingiverse
Please not, I only made 4 holes the case, you can drill the rest with a 1.5mm drill.4x M2 nuts for the T-Beam holder4x M2x6 allen screw for the T-Beam1x 10cm SMA cable, connectors up to you.1x 18650 Li-IonYou can find the wall mount holder for this...
prusaprinters
This case is designed to elevate your low power radio device 30~40 in the air on top of a standard telescoping ‘painter’s pole' available at many hardware stores and keep it protected from the elements. An upgrade from the case I designed for...
prusaprinters
So far I just drilled a hole and it works :-)(01/10/2022) Added v10 with hole for the switch dimensioned for this switchI believe the case fits also the Heltec ESP32 with OLED.remixed from https://www.thingiverse.com/thing:3237860PS.- I am below...
thingiverse
Two options for the ePapers, both 200x200 pixels resolution: Waveshare 1.54 and Heltec 1.54. Mind setting the right class when you compile it using ESP-IDF, also doing a idf.py menuconfig And adjust display configuration to match the connected...
thingiverse
* NEWS: ESP-32 Heltec with Oled (128x64) -> There's a new experimental case for an ESP32. We used Heltec ESP32 with Oled, you can check the HACKADAY instructions in the link below. This is a work in progress and only schematics are provided, but it...
thingiverse
## ESPHOME Code The ESPHome configuration code for this project can be found here https://pastebin.com/iGz8zryn or pizza_oven_sensor.yaml in files section you will need to download the ttf font for the OLED display and place them in your esphome...
prusaprinters
The carrier accommodates: 1 TTGO or similar (HelTec dev boards) 1 Neo 6M GPS board 1 BME temperature and humidity sensor 1 27x25mm vero board as a power and voltage divider board 1 32x25mm vero board as a sensor breakout board 4 LiPo 18650 cells I...
thingiverse
In addition, a cutout for my Heltec-based Firefly Nano Remote receiver was added. This case is very far from waterproof, or even water-resistant, so you'll want to start by adding a conformal coating to the FSESC board to protect from shorts. ...I will...
thingiverse
I have a touch switch version of this here: https://www.thingiverse.com/thing:2778841 using Heltec HTTM-SCG touch switches. Edit 02/04/2017: I added "Stubby" button and included the wall box right here too. Edit 12/10/2017: I replaced...
thingiverse
This project offers parts to mount your Tinderbox pedal built on Heltec ESP32 microcontroller to a case of your choosing. The parts contained on this project mount the ESP32 to the front/top panel and the USB linked below to a punchout on the case...
thingiverse
The carrier accommodates: 1 TTGO or similar (HelTec dev boards) 1 Neo 6M GPS board 1 BME temperature and humidity sensor 1 27x25mm vero board as a power and voltage divider board 1 32x25mm vero board as a sensor breakout board 4 LiPo 18650 cells I...
thingiverse
Even though Sonoff makes a touch plate version of their switch, I thought it would be fun to make my own version using Heltec HTTM-SCG capacitive touch switches that are about $3.40 US each. Along with a $6.00 Sonoff basic and a little plastic you...
cults3d
Even though Sonoff does make a touch plate version of their switch, I thought it would be fun to make my own version using Heltec HTTM-SCG capacitive touch switches that are about $3.40 US each. Along with a $6.00 Sonoff basic and a little plastic...