hex bit storage case 3d models

Hex bit storage case (up to 32pcs + adapter). ... External parts (not for printing): 3x70mm wire (rotation axis).

Here it is, the print in place hex bit storage case for 1/4" bits. No Supports I printed mine out of PETG at 0.3mm layers but I think finer layer heights would definitely help with the fit of some of the hex bits. I had a few spots that were a...

Bit holder designed to fit into Dewalt Hex Bit storage cases. As you can see in the pics, Dewalt hex bit kits come in these storage cases that have a certain dovetail pattern in the sides. This model allows you to add and/or improve the storage...

Both sets of bits use a 1/8" hex key to adjust set screws, so it made sense to have storage for the hex key along with the bits. I went through 4 iterations to make sure everything fits well inside the case. The design is 3 separate pieces, but you...

... place for hand screwdriver. ...I used hex H6 bit for screwdriver holder into box. The hex bit is only pushed to the center of the box. It will hold the screwdriver. My inspiration is hier: Hex Bit Storage Box for 1/4" Hex Bits by 3Dizain - Thingiverse

***Euer Schmelz freund*** Hex Bit Storage Box ***would scale to 103% Storage Box*** Make sure you have good bed-adhesion. You can use a brim to be safe. Use 0.16 mm layer height for printing. No supports required. ***ich würde auf 103% skalieren...

... however I am very happy with the end result. The purpose of this model was to create a storage container with the Hex Bit holder found here: https://www.thingiverse.com/thing:4287182 There is a photo showing the hex bit holder inside the box above.

Small capsule for storing 1/4" hex bits. ...Fits 12 bits nicely.

My printer is less well dialed in, so i wanted a bit storage box that allowed more tolerances and still hold my bits. Changes added when remixing: - The 6.35mm(1/4") version needed some rearranging since hex slots became too wide for the cover. -...

Wanted a way to organize some hex bits on my pegboard, couldn't find anything that was exactly what I wanted.  I love the interchangable pegs on RyukyuD's Modular Tape Storage.  His design makes printing the pegs easier, so get the pegs...

English (Deutsche Beschreibung siehe unten)I offer the hex-bit-storage in several variations:This version offers room for 7 x 3 bits onlyOther variants are:8 x 3 bits only8 x 3 bits plus Wera RapidaptorAll variants offer additional options...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1118772 Instructions Using the following options: _rows = 12 _add_intersect_holes = 1 _strShape = hex _rad_rounded_edge = 3 _diam = 8.2 _cols = 12 _depth = 25

... at the back. And.. This makes place for a label in front :-) FYI I have to scale the tray to 106% to make it fit my bits and the box to 108% to fit the tray right off the printer. ...Probably the settings on my PLA printer that is a bit off.

Mini Hex Bit Case Bit Halter Box

Hex bit storage box for ikea skadis board 0.16 support +

I liked the idea behind RoyToreHofstad's remixed Hex Bit Storage Box, with the cuttout to push instead of the tab to pull. I found the back of the case was too weak with the cuttout, so this is 1.5X as thick on the back. I also added small rails on...

its an 8 way hex screwdriver bit holder

Case for drill bit set: 1,5 mm 2 mm 2,5 mm 3 mm 3,2 mm 3,5 mm 4 mm 4,2 mm 4,5 mm 5 mm 5,5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 12 mm and small storage space. Use 2mm thick metal wire as the axis! Print instructionsYou may need to cover the printer!

English(Deutsche Beschreibung siehe unten)I offer the hex-bit-storage in several variations:This version offers room for 8 x 3 bits and for the Wera Rapidaptor(If you have no use for the Rapidaptor, see the other variations below)Other variants are:8...

This is a case for 52 hexbits with a diameter of 4mm. I designed it for my bits of the WowStick. ...The size of each hole is 4.5mm to ensure a loose fit.

## Parametric hex bit holder Hex bit holder for standard 6.35mm / 1/4" hex bits. This holder can scale from a single hex bit through to as large as your machine can handle, I've rendered 100x100 in fusion 360 and took around 5 minutes on my 2013 I5...

I needed to organize my loose hex screw bits and looked around for a simple solution. ...I did find solutions but they where either too small, to large or had sharp edges.Here is is my solution to the problem…There are many different sizes to choose...

Holder for my hex bit set. ...A total of 40 bits fit in the holder.

A nice compact case to store your drill bits, perfect for your tool bag or workshop.

I have a lot of ¼ hex bits laying arround and I was getting tired of the caos everytime I wanted one, so I created this bit holder with the magic number of 100 bits!The model is based arround the Inside Out electronics openscad model but I'm picky...

Used with these AliExpress-Items: 10 pcs Torx 1/4" Hex Bits T6 to T40 7 pcs Hexagon 1/4" Hex Bits H2 to H8 10 pcs 1/4" Hex Bits Mixed Set Related items: Drive Socket Storage Box Hex Bit Storage Box for 50 mm 1/4" Hex Bits Edit: I added two more...

Changed from my previous version and now using four 8x3mm magnets, one placed at the bottom (layer 1) and under each hex pocket so that the magnets will hold the bits in the rack and also secure the rack on a metal surface. At layer 13 you will be...

I'm currently putting most of my hand tools up on the wall using "french cleats" and I wanted my assorted hex bits up there as well. While the holder was destined for the wall I also wanted to be able to place it flat on the table, which is why I...

The key factor is the printer allowance to get the desired fit of the bits in the base. To assist in working out the correct size I created a test part with 0.1 mm across flat steps, I recommend you print this part and try your bits in to work out...

Only changes are I added two embedded 10x2mm magnets into the base and chamfered the bit openings slightly. About 19 minutes into the print job (if you use my .3mf file) is a pause for inserting the two 10 x 2 mm magnets. If you find the magnet...