hhkb 60 case 3d models

The following additional components are required for mechanical assembly: - 16 M3x18mm socket cap screws - 4 M3x8mm socket cap screws - 4 M3x12mm socket cap screws - 1/16inch thick neoprene foam for the gaskets - 1/8inch thick neoprene foam for...

In this case, the top part and ramp is comprised of two components, while the bottom case is made of three parts. This was done to avoid misalignment issues, and mitigates the issues associated with chopping up these parts (ideally these wouldn't be...

Finally, the ramps slope the case and give additional structural rigidity.The case is chopped in a 2-3-2 configuration. In this case, the top part and ramp is comprised of two components, while the bottom case is made of three parts. This was done to...

......This board is inspired by the HHKB 60% case by Julian, with the same 2-3-2 structure so the case can be assembled with only screws and no need for glue. All of the models are made by myself other than the ramps which are from Jilian's original case.

This is a true HHKB (Happy Hacker Keyboard) style plate, including the 6u spacebar. Thickness is 1.7mm, but the plate cut on the laser cutter shown is 2mm and works as well. 1.7mm is just what is specified for Cherry MX switches and 2mm is at the...

This is an HHKB version of kkatano's Bakeneko60. ... Please follow instructions on kkatano's github https://github.com/kkatano/bakeneko-60

60 percent gh60

Summary Stand vertically for HHKB(Happy Hacking Keyboard)

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2K0xiiAa3hb

Leg for HHKB Lite2

This is a keyboard case for a 60%.

Case for 60% keyboards. Use M2 heat inserts. ...

Keyboard roof for HHKB Professional Hybrid 1. ..."keyboard_roof_for_hhkb.stl" x2 (symmetry) 2. "hhkb_left.stl" & "hhkb_right.stl"

this is an insert for budged 60% plastic cases so you can easily press the flash button without the need of a tool, or to ease your mind and shut that pesky little hole at the back of your keeb. it might fit on other cases but I don't have any to...

60% tray mount keyboard case High profile, 6.8-degree typing angle, standard dz60 mounting, 2 middle standoffs are removed for they add to typing stiffness. Modeled using dz60 specification I found on the internet as reference. The measurement...

... CASE. ...Standoffs are for xd75re, may need to remove or add stand offs for 60% keyboard. USB opening is a little big, modify as you need. Assembled with super glue, and clamps. ... UPDATED 11/9/18: Fixed standoffs, and shrunk the plug opening.

A 60% keyboard case that fits the Pok3r layout. The screw holes and sizes should match that of other Pok3r and 60% keyboards. I am using it with a GH60 Satan PCB. It is designed with two pieces so it can fit on a 200mm*200mm printer. I printed...

This is a case designed to fit mainly the Pok3r, but it will also probably fit other 60% keyboards like the Poker II, etc. I've only tested it with the Pok3r and it does fit. I printed it on a Lulzbot Taz 5. ...It's based off of the dimensions from this...

A tofu 60 with a little thicker bezels on the sides and morrel 60 internals.

This bracket is for securing the teensy dev board to the HHKB case. This is for the DIY-version of Hasus alt-controller for the HHKB to be able to run QMK. Instructions to build the alt-controller can be found here:...

High profile case for gh60 compatible keyboards, 6 m2x4 bolts needed.

http://www.thingiverse.com/apps/customizer/run?thing_id=169491 Instructions Using the following options: cone = 0 inner_cone = 1 ridge_thickness = 0 ridge_displacement = 3 height = 60 outer = 15.6 clearance = 0.3 ridge_height = 2 inner = 11.4 $fn =...

This model is a zero tolerance remix of the popular Bakeneko 60% keyboard (https://github.com/kkatano/bakeneko-60) by kkatano.Please use this link to see the “official” documentation if you have any questions about the board!As you need glue to keep...

This is modeled after the Tofu60 keyboard case and should fit most plates and PCBs. There are no stand offs for screws, the PCB kinda just sits on the lip inside the case. I printed my in two parts on my resin printer, I didn't bother to glue both...

The case from brandonforty2 fit my DZ60RGB ANSI V2 perfectly but I wanted it higher and more angled. ...Printed at 100% with 25% gyroid infill, sound is great but it was ever so slightly too tight, I would scale up a mm or two to make it fit more...

Changes from the original split keyboard case models: Made the opening a couple mm wider, so the XD64 PCB would fit in the case with a little room to spare. Added the missing screw mount to the left hand model, the one that sits on the rib near the...

7 inch cyberdeck design for raspberry pi and a hhkb keyboard.

this is a keyboard case I made to house and protect my Tofu 60 as it is very heavy and has damaged items in my backpack when I've traveled with it. Keep in mind the dimensions of your keyboard are most likely different from mine. It was too long...

https://github.com/Leask/HHKB-Trackpad-Nest A 3D printing HHKB-Trackpad-Nest project can merge your HHKB and Apple Magic Trackpad 2 into one piece. That will make you work like using a MacBook Pro keyboard-trackpad layout but with a fantastic HHKB. ...

Dust cover for the HHKB. The STL is for half so needs to be printed twice. ...I printed mine in Taulman Tech-G (PETG) at 0.3 layer height and attached the two halves using a soldering iron.