hobie mirage drive replacement 3d models

... on this part for crossing open waters, but it makes a suitable spare. I hope this DIY solution proves helpful to my fellow Hobie kayak paddlers and peddlers out there who value the Mirage drive as part of their Hobie Tandem Island sailing kayak.

The "Mirage Drive Fin Guards" are meant to protect and extend the life of the leading edge of a mirage drive fin toward the ends where they are most vulnerable to cuts and gouges which can occur from minor collisions with shallow water obstructions...

I'm looking for a replacement part, specifically an "IDLER PULLEY" with item #81121001. ...I've designed a custom version in black ABS with 50% infill using my 3D printer and it's been thoroughly tested on the water several times now, performing...

The Mirage Drive sprockets are connected by the idler cable, which is held firmly in place by the idler pulley.

If a padeye on your kayak breaks or is lost then this is can be a useful replacement. ...In addition to the printed part you will need an eye bolt to screw into the center hole; I used ¼" with 20 threads per inch in this design since that is easy to...

This design is a fish finder mount on a Hobbie iTrek 11 or Mirage i11s ( old name) it's design to for a Garmin STRIKER 5cv but can work with any Garmin fish finder GT20-TM For other fish finder, you just need to design a different Tranducer mount One...

This design is a fish finder mount on a Hobbie iTrek 11 or Mirage i11s ( old name) it's design to for a Garmin STRIKER 5cv but can work with any Garmin fish finder GT20-TM For other fish finder, you just need to design a different Tranducer mount One...

I engineered a novel pulley system for my Hobie 16 jib sheet car, taking advantage of its full potential. ...I've attached the SolidWorks files, allowing you to refine and perfect my design if desired - feel free to give it a try!

The enigmatic Mirage - a Warframe as elusive as her mirages themselves. ...Her very presence is a masterclass in misdirection, leaving enemies bewildered and off balance.

Based on ilustrationhttps://www.deviantart.com/kp-shadowsquirrel/art/Mirage-Poses-4-824865611

Counter-Strike's iconic Mirage map is now playable in Minecraft, complete with a fresh new skin that brings the competitive feel to your blocky world.

I designed it specifically for my Hoodoo Impulse 120, but it should be able to fit any kayak with a mirage drive slot with little to no modification. The trolling motor shaft section was designed specifically for a WaterSnake T24 and I use adhesive...

Replacement for the stepped top of a Gotek drive. If you wish to use your Gotek drive externally without housing it in an old 3.5" metal drive case. Pop some rubber feet on the bottom of the Gotek and print the replacement top case part. Just...

This is a print that replaces the DVD drive slot on a laptop and either is a blank copy for, or has a slot that holds an additional hard drive.

This particular USB thumb drive fits like a glove into one niche of device users, though its unique features might spark creative problem-solving in other applications too. ...Expect the enclosure cap to hit shelves at some point.

The drive gear shattered on my Whirlpool icemaker. I removed the three small tabs from the original version, realizing they served no practical purpose, and created a simplified design instead. This repair has been functioning smoothly for over a...

Just a replacement case for a Schellenberg DRIVE 60853.

Replacement drive cup for low budget rock crawler HBToys ZP1001. ...Printing in PLA the replacement does wear out again after a few drives, ABS would solve this issue i think.

Replacement Rubber for Tormek Drive Wheel SA-250. Maybe it works with other Tormek Versions like T7 and SG-2000 too. ...

... also includes MK5-compatible screwholes and tongues and a cover to hold the plunger in place. For optimal results, print with ABS and replace the old filament drive components while assembling the extruder, starting with the motor installation last.

This is a replacement drive shaft for the Kitchenaid Pasta Roller. The original equipment includes a shear pin to protect the mixer. Kitchenaid does not make a replacement shaft and expects you to buy a whole new unit if you break the pin.I have...

This replacement door fits perfectly into the built-in floppy drive slot of the Apple III, also suitable for the Apple III Plus model. ...The hinge pin and socket design needs minimal reinforcement with additional supports, resulting in a smooth...

I had to replace some defective USB flash drives that were damaged beyond repair. ...To fix them, I carefully disassembled the housing by removing the circuit board and then crafted a simple new one using just a few basic materials - specifically, glue.

The idea is that, when printed at 100% infill, it will be strong enough to take the drive force from the engine, but will shear across the print lines if the propeller hits an obstruction. In theory, it will be much cheaper than regular springs,...

The drive pulley is a part of the Tefifon that rarely needs to be replaced. But I have a pulley that had a deviation of 0.3 mm in concentricity. So I designed this replacement part. My first print only had a deviation of 0.06 mm in concentricity, so...

... ... Slimmer and tougher than the original case, also have a hole for the indicating light. Secured with bolts to the M3 threads on the drive. The hard drive itself should be pretty standard, but the usb connection and light can vary between drives.

The drive pulley is a part of the Tefifon that rarely needs to be replaced. But I have a pulley that had a deviation of 0.3 mm in concentricity. So I designed this replacement part. My first print only had a deviation of 0.06 mm in concentricity, so...

Many drives therefore no longer run well and make noise.So I decided to design this replacement part. When mounted to the device it almost looks identical to the original part. But all invisible parts have been optimized for 3d printing, stability...

The large gear is available here: https://www.thingiverse.com/thing:1027096 Based on [this](http://www.partselect.com/PS380968-Whirlpool-628210-Icemaker-Drive-Gear.htm) link, this gear will work on the following brands: Whirlpool, Admiral, Estate,...

You'll need to glue this part to the tabs on the front of the DVD drive on your PS2. I highly suggest printing this in black ABS and vapor smoothing it to match the original appearance of the PS2. ...I opted for PETG instead, but it turned out pretty...