holosun 509t mounting plate 3d models
528068 3d models found related to holosun 509t mounting plate.prusaprinters
This is a mount for the Holosun 509T pattern of micro optics. It's designed to use 30mm M3 hex head capped screws and hex nuts. </p><p>I've tested printing this with up to a 0.6 nozzle and 0.2 layer height- smaller nozzles and layers will work...
grabcad
This Model is a mounting plate for interfacing the Holosun 509T with the Sig Sauer RX cut.Please be aware that the screws used are weaver screws 3-48.You can machine it from a solid piece of steel. ...I had mine printed from 316L.Along I provide...
thingiverse
These were made for my Holosun 509t to fit the RMR cut on my Zaffiri Precision slide. The slide cut from ZP did not fit the adapter plate that came with the red dot and I was not pleased that it did not co-witness with my sup. height sights. These...
thingiverse
These were made for my Holosun 509t to fit the RMR cut on my Zaffiri Precision slide. The slide cut from ZP did not fit the adapter plate that came with the red dot and I was not pleased that it did not co-witness with my sup. height sights. ...
thingiverse
Adapter plate for S&W M&P 2.0 for Holosun k series red-dot optics. Printed in PLA, PTEG, and ASA with no issues. ... 100% in-fill.
prusaprinters
Quick and dirty 509T mount, because optics should cost more than the gun, right? /s</p><p>This is designed around the default rail screws, or replacements like the set of 4 Torx screws on Tandemkross.</p><p>Tested with nozzle sizes from 0.25 to 0.6,...
sketchfab
Holosun HS403R scope 3d model Archive contains FBX and Unreal Engine 4 texture pack
thingiverse
... very well with the Bircwood Casey Aluminium Black, but it's fully functionnal! Dovetail locking is for M3x10mm screw and reddot mount is for the original Holosun #6-32 screws. ... Dovetail is 6.2mm / 8.6mm wide (top and bottom) and 2.6mm in heigh.
thingiverse
I wanted to use an RMR red dot, so I modified this GO PRO picatinny rail mount bottom: Thingiverse: 103878 With this RMR / Holosun 507C as a top: https://www.thingiverse.com/thing:4699964 It seems to work ok. There are Holosun models designed with...
grabcad
NTM 3530 series mounting plate for HobbyKing 35mm dia. ...motor Motor holes are 25mm and 19mm centers
thingiverse
This mounting plate is intended to fix the motherboard to a plate. The mounting plate is for makerbase mks gen l v1.0 - v 2.1. ... The dimensions of this motherboard are 84 mm x 110 mm and the screw holes are at 76 mm x 102 mm
thingiverse
A keypad interface plate to allow a keypad that didn't come with one to be mounted to an outer wall, in a location where a different brand/model had previously been used.
thingiverse
This is a mount plate to use a redundant dji phantom 3 smart device holder. ...To reuse it to hold my tablet on my boat when using it as a chart plotter.
thingiverse
Not sure how useful this will be for others but it is a replacement mounting plate for a small Harbor Freight parts washer pump. The bright red one is the original that came on it. Printed with red PLA and the mineral spirits have not dissolved it. ...I...
thingiverse
This was designed to mount a tuner chip to the dash of my truck. The center hole diameter is 12.75mm and it is 20mm deep. The countersunk screw holes intended for #6-32 screws. I have also uploaded the original SketchUp for you remixing pleasure.
thingiverse
Picatinny adapter for Holosun HS407c, also works with the HS507c, Trijicon RMR, and ADE Stingray red dot sights. ... - Requires 1x 3/16" diameter pin to press fit the mount on the picatinny rail
thingiverse
There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I printed mine in ASA, put PLA should be...
cults3d
There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I printed mine in ASA, put PLA should be...
prusaprinters
Picatinny adapter for Holosun HS407c, also works with the HS507c, Trijicon RMR, and ADE Stingray red dot sights. Requires 1x 3/16" diameter pin to press fit the mount on the picatinny railPrint Settings Printer Brand: Prusa Printer: I3 MK3SRafts:...
thingiverse
Pivoting cover for Holosun HS512c red (green, or gold) dot optic.
thingiverse
Compatible with: - Holosun 403, 503, 515 - Aimpoint Micro T-1, T-2, H1, H-2 - Vortex Sparc II - Hi-Lux Micro-Max B-Dot. ... Screw is M5 PRINT AT YOUR OWN RISK!
thingiverse
HOLOSUN HS510C TPU cover from dust and scratch. Easy to put on and off, tight fit. It is printed with supports. ...Layer height 0,2 mm.
prusaprinters
There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I printed mine in ASA, put PLA should be...