hon30 scale 3d models

HOn30 Baldwin tender. The floor is designed for Kato Caboose trucks. You can put their contact strips into these new trucks. ...Also made to fit a MDC/Athearn 2-6-0/2-8-0 motor in the tender or a coreless motor using the mount.

HOn30 Baldwin tender. The floor is designed for Kato Caboose trucks. You can put their contact strips into these new trucks. Also made to fit a MDC/Athearn 2-6-0/2-8-0 motor in the tender or a coreless motor using the mount. ... Category: Hobby

This is a HOn30 slightly shortened Kennebec Central Forney #1 made to fit a Toma Model Works Kiso loco chassis. The real locomotive was converted to burn coal with an extended smokebox. To print tip the body up at 23 degrees. ...After printing file off...

These were designed to use recycled N scale trucks with a center king pin holding the trucks in place. A little reaming of the king pin hold may be necessary. Use of a small screw may work as well. Other size truck should work if spacers are used...

HOn30 Steam Dummy based on Baldwin #12807 Std 5½&8x13 33” 0-4-0 Coke 7/1892 4 5/10-C North Chicago Street Ry #12 Motor Returned as “too small” ~ Resold Mohnsville & Adamstown #1Print roof upside down and sand it smooth."block" file goes into the 2...

This is a HOn30 18' boxcar that might or might not look like the Bachperson On30 model. I used Tichy grab irons, stirrups, and brake wheel. 1015 Microtrains couplers and Microtrains axle length (.540") 36" metal wheels form Eastern Seaboard Models. ...

Queensland Railways QR FJS 4 Wheel Open Wagon For: 1:87, HO Narrow gauge What it is: A low detail 4 wheel wagon (Not up to the quality of a modern ready to run wagon, this is a kit!) No buffers supplied, use HO Cast white metal or Wuiske Models...

(Microtrains length) I used HO scale 2x6's for the decking and Microtrains 1015 couplers. The first Rio Grande flat cars were 90 small 4-wheel cars with a capacity of 5 tons, built in 1871 according to Billmeyer & Small plans, they have been used...

I highly recomend using a SLA printer as you will not get the detail in FDM unless you intend to scale up. The Gilpin Railroad, earlier the Gilpin Tramway Company, was a 2 ft (610 mm) narrow gauge railway in Gilpin County, Colorado, in operation...

These cars were used on the Iron Mountain RR in Pardee MT. ...Modeled in HOn30. Any MicroTrains length (.540") axle wheels will work. 36" wheels in N scale are the correct size, but 33" will fit.

These are for a Fyling Zoo HOn30 18 ton Climax.

HOn30 SRRL style railbus sideframes that fit a Bachmann 44 or 70 tonner truck.

These are tippers used by the Lime Rock Railroad made in HOn30. ...They use MicroTrains length axle wheels and a .020" piece of wire between the journals.

This is a HOn30 Bellevue and Cascade stockcar. Frame uses Microtrains 1015 couplers. ...Trucks use any Microtrains axle length (.540") 36" wheels.

This is a HOn30 motor car for the Eureka-Nevada Railway. It used a newer Kato 11-109 or 11-110 power chassis with the plastic shell stripped off. ... Updated with more detail.

Standard n scale wheels should pop right into the bottom of this car, feel free to glue a microtrains coupler or even a draw bar. ...Be sure to check out my chloe as well!

The real locomotive was hand made and still runs. ...I used video stills to make the drawings. I used a Bachmann N scale 70 tonner with the circuit board removed. ...A 44 tonner would work as well.

This is a single engine shed for Narrow Gauge 009/HON30 trains, though could be scaled up for other narrow gauge scales.

Quincy & Torch Lake early rockcar that was narrowed and shortened. ...I used the trucks from my boxcar here: https://www.thingiverse.com/thing:5131200 Couplers are Microtrains 1015.

Quincy & Torch Lake early rockcar that was narrowed and shortened. I used the trucks from my boxcar here: https://www.thingiverse.com/thing:5131200 Couplers are Microtrains 1015. ... Category: Hobby

Same railbus I have up on Shapeways. ...Will take either a Kato 4 wheel chassis or the Kato 8 wheel chassis.

HOn30 Jackson and Sharp type trucks. ...Use 36" .540" axle wheels.

HOn30 Grove Farm plantation 0-6-0T. ...I used an Aru Model ARU-A4010 chassis on mine.

Standard n scale wheels should pop right into the bottom of this coach, feel free to glue a microtrains coupler or even a draw bar. ...Be sure to check out my chloe as well!

... beam. The donor chassis requires no modification and the body is a simple slip-fit. The bogie centres and axle spacing of the donor chassis are roughly correct at this scale, however the wheel diameters are significantly smaller than the prototype.

The floor/underframe has been designed for a N scale Green Max Brill bogie (Part No 5020) which look very similar to the bogies shown on the Fainges plan, however other N scale bogies should also work. I used fishing line to reproduce the truss rods....

The floor/underframe has been designed for a N scale Green Max Brill bogie (Part No 5020) which look very similar to the bogies shown on the Fainges plan, however other N scale bogies should also work. I used fishing line to reproduce the truss rods....

HOn30 or 009 Narrow Gauge American Passenger Coach this is designed to run on 9mm track.

HOn30 or 009 Narrow Gauge American Mixed Coach, this has a freight area and passenger seating. ...This is designed to run on 9mm track.

I use 1016 couplers and 2 1/16" tungsten welding rods glued to the underside.