hdmi to water hose 3d models
2160553 3d models found related to hdmi to water hose.thingiverse
You really can't say it's useless because you could totally use it as a spray nozzle on your garden hose with an HD water stream... This was a combination of two items from Thingiverse: https://www.thingiverse.com/thing:551238 and...
thingiverse
This adapter will allow you to connect a garden hose to a military surplus water can. ... I use it to add water to the fresh water tank of my travel trailer while boondocking.
thingiverse
Output adapter for water heater to garden hose. For bench testing a water heater away from the normal hookups. 3/4 NPT/ FIP to garden hose male Print at 100% infill to avoid leaking between layers. May need center drilled out, teflon tape to...
thingiverse
Water heater heater adapter for bench testing a water heater in garage with a garden hose. Print at 100% infill should avoid leaking through layers. 3/4" NPT/ FIP pipe threads to garden hose adaptor. Will probably need center drilled out (I modeled...
thingiverse
This clip simply helps to keep a Micro HDMI adaptor connected to a HDMI Cable
thingiverse
This is a 3D model of a Hose adapter for fish tank pumps. ...Mine broke so I needed to produce one to keep the fun running !
thingiverse
A solution to connect a standard Gardena hose fitting to a HDMI cable.
thingiverse
Simple connector for 22mm water hose to 17mm socket of water jug
thingiverse
Box printed for an HDMI to VGA board. Top and bottom, both snug fitting. ... Friend had the board and no case, so I made one.
thingiverse
This is a box to fit a [HDMI to CSI Adaptor](https://www.arducam.com/product/arducam-csi-hdmi-cable-extension-module-15pin-60mm-fpc-cable-raspberry-pi-camera-specific-pack-2-1-set/) Couples nicely with the [Raspberry Pi Camera...
thingiverse
I needed that to connect a water hose to a flower pot. ... Too lazy for shopping, so I just print it.
thingiverse
used parts: HDMI to RCA converter https://www.aliexpress.com/item/32815095086.html?spm=a2g0s.9042311.0.0.27425c0fFEunVL Headphone amplifier: https://www.aliexpress.com/item/32873798605.html?spm=a2g0o.detail.1000016.1.332a115c4clxZE&isOrigTitle=true...
thingiverse
Solder the ground wire that is next to the 5v wire on the VTX to a ground pad on the hdmi converter. Cut the usb plug off the fan, pass the wire through the printed lid and expose and tin the wires. Solder the power wire to the same side of the...
thingiverse
... This adapter provides an M25 Male on one end and a Male Garden Hose Thread on the other, allowing the jug to be used for pouring into another container (say, an RV) and not just dispensing. Be sure to only use garden hoses marked for Potable water!
thingiverse
Adapter for 10mm (inside) diameter water hose to 3/4 inch (house installation water system) for RV's. I designed it because mixer taps for Campervans are silly expensive and ugly. Connect your water hose and use a screw clamp on the one side and...
thingiverse
You're going to need one of these 1$ hdmi-microhdmi adapters and scrape clean, rubber from it. Both halves should match nicely when printed with 0.12 height, 0.2 width @ 200C. ... To save space, there are no clamps or snaps, so you need to use a little...
thingiverse
For watering the tomatoes in fathers garden we needed the possibilty to adjust the flow for each plant separately. To fix the lever inside the housing, just melt it a little and press with a screw head or something like this. ... This was made for a...
thingiverse
So I designed an adapter to a 32mm spiral hose which is commonly used for this purpose. For better printability the part was divided in two parts which have to be (super)glued together after printing. For a better watertightness I recommend to coat...
prusaprinters
I used it to not bend the hose for a 6000l/h water pump for our pond.The adapter consists of two parts. The only reason it has been designed like this is to add extra stability to the inner thread. Two parts allow different printing orientations. By...
thingiverse
A connector for 3/4" Hoses (19mm) to 1/2" (12mm) If your fit isnt 100% use two hoseclamps for tightening
thingiverse
An adapter for 1" female to 1/2" male water filter fittings. I have a 1" BSP connection under the sink and my water filter came with a 1/2" connection. ...I would recommend a 1" grommet on the 1" side for a better seal
prusaprinters
The super glue is required to get the part air tight.Once the glue has set insert it fully into a garden hose (something like Gardena Classic, 13mm or ½"), and fix it with a hose clamp.Pressure limits are 6 bar with a Dunlop valve, or 10 bar with a...
thingiverse
Needed to try connecting a washing machine to a water canister for use without running water, although this form of a tube adapter is probably useful for many other situations. The sizes I used are for very specific combination, but decided to make...
prusaprinters
The fine thread M22x1 is often used for in house water taps. You need in addition a O-ring and a rubber gasket for the connection between adapter and the water tap. Printed with 0.12 layer height and in PETG.
thingiverse
Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...