honeycomb bravo 3d models

TPU trim wheel cover for Honeycomb Bravo.

737 Levers for Honeycomb Bravo throttle

Modification for the HONEYCOMB BRAVO to include detents for Airbus

This is a storage rack for Honeycomb Bravo handles that can be mounted. One file is for angled rack and can be mounted on horizontal or vertical surface. ...Also a file for horizontal surface with straight storage mounts.

These are dust covers for Honeycomb Bravo Throttle Quadrant levers when you don't want to take the levers out and use the standard supplied dust covers. ... Do note that there are 3 the same and 2 that are slightly different shapes which are in the...

This is a rough guesstimate of the Honeycomb Bravo throttle based on the Alpha flight yoke dimensions and pre-production photos of the Bravo throttle assembly. ... Modeled mainly for my sim cockpit construction planning, so low detail just to work on...

This is a handle for the stock Honeycomb Bravo commercial levers that makes them a little more substantial. They make for a better feel when flying quad-engine jets. The handle is loosely based on 747 throttle handles, they enclose the tops of the...

These are the models I made for a replacement Honeycomb Bravo trim wheel. I bought a preowned Bravo sight unseen and the previous owner had broken off the trim wheel. I'd gotten a good enough deal that, after verifying the electronics worked, I...

Full width IPAD stand for the HoneyComb Bravo Throttle. ... Made with Lightning infill ad 20%

This is add-on to "Honeycomb Bravo flaps Boeing style" LINK: https://www.thingiverse.com/thing:6095894 Spec 2 cages are compatible with this design. Flap lever functionality is mimic Airbus style. ... Inspiration for this design came from...

This is a snap-in cover for the bottom of the flap lever on your Honeycomb Bravo throttle quadrant. Very simple part that just makes the tab feel solid (like the real thing) rather than open on the bottom surface. The tab is shown removed in the...

ATR Throttles designed to fit the Honeycomb bravo throttle system used for flight simulations. Currently Available - Throttles 1 and 2 (Number 1 is slight larger than number 2) - Condition levers (numbered) Work in progress - Brake ...

A remix of https://www.thingiverse.com/thing:4801776 to allow use of tablet on Bravo throttle without interfering with rotaries. ...Using Samsung Tab A 8"

A set of classic twin Cessna styled control levers designed to work with the Honeycomb Bravo throttle quadrant.

This was made on Tinkercad to fit onto the Honeycomb Bravo Throttle Quadrant. ...The only thing you need to add a spring (got mine at ACE hardware for a few bucks).

For: X-Plane 11, FlyJSim Q4XP Q400 Aircraft when used with the Honeycomb Bravo throttle. This is a stopper so that when you idle your throttles in DISC you will have the correct height for instant response. ... Designed to work the stock response...

This is a holder for labels made specifically for different types of key assignments for the Honeycomb Bravo buttons. I am making the labels using a word processor and printing both sides and then laminating the sheet along with some pre-flight...

Throttle, prop, and mixture levers for the Honeycomb Bravo throttle quadrant, closely modeled after the PA28R Arrow III style levers. Fusion 360 files included in case you want to modify them. Printing tips: Prop and mixture handles can be...

This is a Trim wheel cover for the Honeycomb Bravo throttle quadrant. It's a remix of https://www.thingiverse.com/thing:4724402 with 2 major changes. 1) The wheel size has been increased to as large is it can go before hitting the back. 2) The...

Made for the Honeycomb Bravo Throttle Quadrant GA throttle levers. This attatchment for the Bravo's GA throttles, bulks out the heads of the levers to be more like the Cessna Citation CJ4's throttle levers. Thus giving a feel more closer to that of...

These hand grips/handles were made 1:1 with measurements taken from the official Boeing 737-800 specs.   Instructions:Unscrew the existing small handle from the 2 engine honeycomb bravo airliner handlesPull the small finger grip...

1:1 scale replica Boeing 737 throttle grips for the Honeycomb Bravo Commercial throttles. I thought that the default Honeycomb commercial throttle grips were way too small, so I designed these ones. They measure 50mm x 30mm x 30mm. They are...

Chunky throttle handles for the Honeycomb Bravo Throttle Quadrant. **UPDATE**: April 2 '21 - The left hand skewed offset handle had a modeling error that I never detected. I also never test printed it originally, but have since tried the area of...

This is a mount that can be used on the bravo or alpha honeycomb products. ...it will work for a tablet / laptop / keyboard etc...

I created this to hold a keyboard with a red led for my bravo quadrant for lighting and easy access keyboard. ... I used the stock bravo screws to mount and use hot glue to put the base and top together

I disliked that the bottom of the Bravo flap lever was unfinished as you need to flip the lever up to retract the flaps. This is a simple cover to smooth out the bottom surface of the lever. It's a friction fit, so no permanent change, disassembly,...

Original design is from Ross Barlow from www.flapmodster.com. http://www.flapmodster.com So this will categorised as remix. I found that Flap cages are quite weak from point between lever cover and cage-bar. So i changed the design and added...

Reconstructed in CAD to design my own flight simulator. ...Basic dimensions measured and so far ok.

This is a small flat surface that allows you to use your mouse atop the honeycomb alpha or bravo throttle quadrant. ...Designed to be printed in PLA