nzxt h510 custom panel 3d models
1175899 3d models found related to nzxt h510 custom panel.thingiverse
The reason for creating this is because I noticed that the NZXT H510 Elite has terrible airflow. I created this spacer to open the front panel slightly enough to increase airflow and not disturbed the aesthetic of a closed glass case. ...Enjoy.
thingiverse
For the inside pieces I used 2 walls, 0 bottom and top layers 30% cubic subdivision for the pattern (pick whatever you like) I did the hole with the grinder and its dimensions are 160x300mm
thingiverse
I had my GPU arranged vertically, and the fans were almost touching the glass panel. Looking at temps, they went up to 84-85C on my GPU after 5 minutes So adding this seems to drop the temp to around 80C I may try further distances to see how...
thingiverse
Casefanholder 120mm for extra Fans on the bottom of your NZXT H510 Elite Case
thingiverse
This is for a video. ...https://youtu.be/NaTBuYsSpjU Made for NZXT H510
thingiverse
shorter feet for the NZXT H510. may also fit H500 but can't confirm it. "ohne" version with flat bottom and one with indented bottom Print with support. ...(x/y dist ~0.8mm)
thingiverse
One of my H510's foot was broken so i remade it in a stronger version on the parts that broke. ... You need to keep the screw and the rubber pad that was installed with the old one, you can just glue it on the 3D print.
thingiverse
This is a wall mount for NZXT H510 Elite, but I think it will fit other NZXT cases to. ...Mount is 215 mm wide.
myminifactory
It was designed for my specific setup but it should be able to fit into many rigs with minor adjustments to the height and foot, although I would recommend it particularly for use with the NZXT H510 Elite as the case has a cable managing bracket the...
thingiverse
Anti vibration mount for the NZXT H510 case. If you don't have these special screws that are shown in the pictures than print the files with the name _small_screw however I did not test those. the ending _46 and _35 refer to the diameter of the...
thingiverse
I use superglue to assemble ill add a picture so you can see where everything goes I use 10x1mm magnets I got on amazon and you can buy a mesh filter and cut it to size for some case filtration.
thingiverse
This is an upgrade or replacement kit for mounting my [NZXT H1 Custom panel](https://eigakai.ro/industrial-design/nzxt-h1-custom-panels). It uses pegs which fit into the original mounts, just like the TG panel. The corner guides are used to place...
thingiverse
My GPU was suffocating inside my H510 Elite, so I created a front and side panel for better airflow. ...Air filters coming soon.
thingiverse
just a mount designed with 3080ti for the NZXT H510
thingiverse
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
cults3d
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
thingiverse
Headphone holder for NZXT H510 Elite housing. Trial and error is not for the professional model. ... 15-30% filling for PLA can be used.
thingiverse
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet. Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the...
prusaprinters
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet.Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the case...
thingiverse
This is a hard drive mount for an my NZXT H500. It was intended to reduce vibration and noise of my hard drive, but didn't work out so well for that. Uploaded anyway. ...Perhaps someone can use it.
thingiverse
... supply cover. ...The LCD screen that I used is from this link. You need HDMI cable as well micro USB for the power supply. LCD panel: https://a.aliexpress.com/_mNpSrBr Ordered the 4inch for rpi4. ... Hdmi cable: https://a.aliexpress.com/_mrUurQd
thingiverse
You can't buy thumb screws for NZXT cases so I've made some up, not to big and fit great. Not as chunky as the original screws. ... This will generally fit other cases also, it has a slight thumb grip outer with screw threading for the small flat...
thingiverse
A custom front panel replacement for the NZXT S340 case. Update: added modified top and bottom meshes that have the original style opening for air intake. ...marked as the *_open.stl files Update 4/17/20: fixed scale of the open pieces from...
thingiverse
I ordered a custom front panel for the NZXT H210i from JakefaceCustoms on Etsy. https://www.etsy.com/shop/JakefaceCustoms Love the front cover, but the way it is designed and attaches, it leaves a gap at the top which kind of bothered me. ...So I...
thingiverse
Rather than replacing my entire front panel on my NZXT H1 I designed some spacers to help provide a bit of an air gap to facilitate more airflow. I have a couple of 120mm fans on the back of the case that pull air though when the GPU gets toasty. ...
prusaprinters
Rather than replacing my entire front panel on my NZXT H1 I designed some spacers to help provide a bit of an air gap to facilitate more airflow. I have a couple of 120mm fans on the back of the case that pull air though when the GPU gets toasty. If...
prusaprinters
There's a 0.5mm gap between parts; mask back panel, snap pieces into back panel, and fill gaps w/ JB-Weld or similar. This is to allow everything to fit on the bed and account for tolerance issues. </p><p>Printed with Protopasta CF-HTPLA w/ a...
cults3d
As shown gpu support bracket to help stop video card sag
thingiverse
I designed a sensor panel holder for the H210. Might work with the H510 and H710 too. ...The sensor panel is a samsung Galaxy S3.