hook for ironing board 3d models
2340560 3d models found related to hook for ironing board.thingiverse
This is a simple wall hook to hold my ironing board out of my way.
thingiverse
Ironing board hook in order to hang the ironing table. ... You may hang it inside a cupboard for example, it will save you some space.
thingiverse
A simple hook for hanging up an ironing board. The 'V' of the hook extends approx 60mm from the surface it is screwed to which enables the ironing board to hang neatly without rubbing. Works for me and hope it's of some use to someone else. ...
thingiverse
This is an ironing board hook designed to interface with an off-centered T bar ironing board. ... The end result is simple, yet stylish, and can blend in most decor.
thingiverse
A simple hook created to hold our ironing board on the back of a door. The hook is 31mm diameter and the door hook is slightly oversize to fit various doors. I printed 2 at 0.31mm resolution, 2 perimeter layers, 20% infill. ...
prusaprinters
Starting form the following design https://www.prusaprinters.org/prints/71235-ikea-danka-ironing-board-stand-clip I model one adapted to my ironing board with Fusion 360Printed in Prusament PETG Urban Grey with 0.2mm layer height and standard...
thingiverse
My ironing board was getting in the way so i designed this to hang it up from the top of a tall cabinet in the kitchen. ...There are 6 holes available to secure it but i only used 3.
prusaprinters
A simple wall hook for hanging your ironing board on the wall.The diameter of the leg of my board is 35mm.
thingiverse
Runner for Vileda ironing board (Vileda Viva express Premium+).
thingiverse
How I Designed This I noticed that the frame of the ironing board feet are t-shaped, not a "y" style arrangement as some are, and thought it may be easy to make a holder for it. This top and bottom rack arrangement keeps the board neatly folded,...
thingiverse
In order to gain some capacity inside a cabinet, I decided to print wall mounts for our iron and its associated ironing board. I srewed them in the side wall of a Ikea Pax cabinet. In case you don't want to drill holes in you cabinet, the screw holes...
thingiverse
I made this because all of the ironing board mounting hooks I found on Thingiverse were either too small (the hook for the bar), or did not firmly hold the ironing board bar. The bar socket for this is 23mm, but my ironing board bar is 22.5mm, and...
thingiverse
Clip designed to substitute the broken original one on DANKA ironing board (by IKEA). ...
thingiverse
Over-the-top door hangers for ironing boards are great. But opening and closing the door causes the ironing board to swing and bump the door annoyingly. This accompanying bracket is designed to fit the bottom leg of the ironing board into so it...
prusaprinters
Ironing board replacement feet to protect floors from scratches (fits ~1 inch steel tube legs). Prints OK at 0.3mm. ...Slight scale adjustment may be needed depending on the tolerances with respect to a particular ironing board.
thingiverse
Since the original cable holder on my Leifheit ironing board broke, I designed this replacement part. ... It snaps onto the steel wire of the original holder and holds the cable so it's not in the way when ironing.
thingiverse
Tip on the leg for the Soviet ironing board. Inner diameter 17.5 mm (if it fits too loose, you can either glue it on, or scale it down a bit). Printing is best done with soft plastic. I used FDplast SBS Glass, infill 100%. Наконечник на ножку для...
thingiverse
A simple, rounded cylindrical adapter to make the rubber feet of my ironing board fit on its tubing. It is parametric, customizable, see the SCADs. The Ironing Board Rubber Foot Adapter 190710c is the most matured version. ... Settings and...
thingiverse
Should work for most ironing boards with a similar leg design as seen in the pictures. I also included a single hook so you can adjust it just right for your board. The single hook will work for many other applications also. This fits on an...