hoover windtunnel 3d models

My design for the old Hoover Windtunnel pipe cover. Care should be taken to install as the hinge pins are thin, but it seems to be a really good fit. I printed on my Ender 3 with PLA. I printed with a 5mm nozzle set to 4.5mm bead. ...I used supports for...

This adapter enables seamless connection of two Hoover Windtunnel vacuum cleaner hoses in tandem, overcoming the conventional obstacle posed by small tabs on one end of each hose. ... This component is now free for public use, accompanied by my gcode...

A replacement foot pedal for the Hoover Windtunnel vacuum requires you to remove the metal plate from the original device. Printing this design upside down is likely necessary. I tested it on October 24, 2018, and it works perfectly. However, you...

This is a bottom hose and cord bracket for a Hoover Windtunnel 3 vacuum cleaner. I said I'd never buy another Hoover vacuum cleaner, but my wife found one at a church thrift shop for $20. She tested it and sent me a picture while I was at Home Depot,...

I've got a Hoover Windtunnel 3 Vacuum. Today, Hoovers are made of plastic, and they break a lot. The brackets for winding up the power cord are no exception. A few years ago, I designed a replacement bottom bracket. It was a lousy design... It...

This is the second WindTunnel Hoover vacuum model I've seen with a recurring issue - the wheel axle passes through an unsupported plastic tube at its top. Over time and repeated stress from vacuuming on various surfaces, going up and down stairs,...

Foot pedal assembly Hoover WindTunnel UH70120 Hoover T2 304233001 You'll likely want to print this upside down. Tested on Oct 24, 2018. Works fine. May need to trim the catch corner a bit if it sticks. I recommend printing this with a strong...

3d-printed replacement rollers for a hoover vacuum cleaner to prevent the base from getting sucked down to the floor. ... These are not the spinning roller brush, these are the floor guides.Replaces missing rollers.26mm width, 19mm diameter, 3mm dia...

Replacement foot pedal latch for Hoover Windtunnel 2. The most difficult part of this print is incorporating the metal "spring" (V shaped piece of metal) from the original component. The plastic pedal broke on my vacuum cleaner, but I removed the...

I fitted the holder exactly where I needed it, then drilled a precise 1/8" hole through the hose holder. A small wood screw kept it securely in place. The attachments slide smoothly up through the holder. Printing Settings Were Crucial Printer...

I replaced the canister release on my vacuum with a new one that I designed using Fusion 360. The original release was made of injection molded plastic, which turned out to be too weak for its purpose. After several revisions, I came up with a...

The retaining clip that secures our vacuum tube snapped off. ...We designed a replacement using Fusion 360, fabricated it with a 3D printer, and now it functions perfectly.

I imagine this part is used for other Hoover WindTunnel Air models too. To use this part, the original spring and screws are required. Additionally, you must cut and attach a piece of foam identical to the original part, to maintain vacuum seal. ...

Replacement hose switch for HOOVER UH70120 T-SERIES WINDTUNNEL REWIND PLUS Known issues: - Switch needs to be shaved down on the flat bit a little in order to secure the hose - After shaving, switch won't release hose adequately - The spring...

https://www.usavacuum.com/Hoover-U8130-WindTunnel-V2-Bagless-Upright-Vacuum-Parts-s/1382.htm To remove the broken part: - remove #49 Final Filter Door (pops off) - remove #42 Final Filter - remove screws #34 (qty 2) - remove screws #29 (qty 2) -...

Replacement Upper Cord Wrap Hook for Hoover WindTunnel UH72600 vacuum. The original Hoover part number is 521067001.This isn't exactly identical, but when our vacuum fell over and broke the hook, I didn't want to pay $20 or more to get a...

Vacuum cleaner wheels for the ancient Hoover WindTunnel broke and needed to be replaced. Printed then in red for two reasons. 1) They look sharp 2) You buy red filiament and think your going to use it but don't The pictures of the wheels are...

Hoover demanded threefold the price of the replacement part for shipping, prompting me to grab a measuring tape and fabricate one on my own. ...The sturdy piece snaps firmly into place, ensuring it won't be dislodged without sustaining damage.

Hoover wanted 3 times the cost of the part to ship it. So i grabbed a ruler and made it myself. Snaps in solid so you wont remove it without breaking it..... ... Update: Still trying to refine this, little cleaner and it locks in better

This is the 3D printable (Dutch) windtunnel. Better instructions will follow, but for now the main things are: - The left side of the tunnel is called "aanzuig venturi" and consits of 8 parts which can best be printed upright. - The right side...

My own design of a Supersonic Windtunnel by perfoming handcalculations and then generating a CATIA model of it.

Created these Nozzles for my Hoover...

Human vacuum cleaner.

For Snapmaker A350 CNC

Happy Birthday

Just my design for a wider hoover added

Here is the rewritten text: $35mm Hoover Holder Staubsauger Halterung

As seen at The Hoover Dam surrounded by a serene lake and mighty Colorado River.

The end nozzle of our hoover broke so I modelled this one. ...Works just fine.

The Hoover Dam stands majestically alongside Lake Mead and the mighty Colorado River.