how to change filament mid print ender 3 pro 3d models

Advanced Ender 3 PRO Filament Holder featuring Dual High-Performance 609 Bearings for Enhanced Smoothness and Reliability.

Works fine for the Ender 3 Pro and prevents the filament spool from falling off the printer.

A BTT Smart Filament Sensor mount for the Ender 3 Pro. It uses a press-fit mount as well as screw mount to make sure that it fits securely. It was remixed from a mount by anthonyr82. ...His was meant for an Ender 3 v2 with a dual gear extruder and...

Ender 3 pro filament guide for PTFE tube It works with Ender 3 pro genuine Bowden plastic extruder or metal extruder like in the picture.I prefer this design over the bearing roller type, less inconsistent friction.You should print like the last...

I copied the guide directly from @Holspeed's design because it works perfectly and I appreciate how easily it slides over the bracket on my Ender 3 Pro. The filament sensor is a combination of several designs found here, with special thanks to...

The original bracket did not fit the Filament Runout Sensor I got from Biqu with my BTT SKR Mini E3 v2.0; this Sensor is also sold on AliExpress here: https://www.aliexpress.com/item/32967243103.html The Runout Sensor I got is bigger than the one the...

You can find spool holders here, that fit with the Ender 3 S1 Pro. Drill a 8mm hole into the shelf and screw holder and lid together. You have to remove the metal plate at the back of the filament guid. Not sure how it performs for high prints,...

... and a guide (flat or open) from the original filament guide. Thanks! Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.20 Infill: 20% Filament: Inland PLA+ PLA True Red Category: 3D Printer Accessories

... the sensor to screw it on. The short PTFE tube will guide the filament beside the Z-rod.See also my reinforced version for the dual gear extruder: https://www.prusaprinters.org/de/prints/104866-smart-filament-sensor-holder-for-ender-3-pro-for-d 

This spool holder for the Ender 3 Pro is long enough to hold 2.5 kg filament spools. ...The spools rest on small rollers and therefore rotate more easily.

This Thing is based on Bowden Filament Guide with Cable Holder for Ender 3 Pro by DanielStoelzner. Creality updated their Ender 3 Pro design again and moved the entry hole for the extruder a millimeter or two more out of place. After upgrading to an...

So if you own either an Ender 3 or an Ender 3 Pro, you can easily have a foldable filament spool holder from the CR-6 SE! Some minor filing may be required due to a tight fit. ...Simply use a 40mm M3 Allen screw with a nut to mount the holder and reuse...

This is a simple all-in-one filament guide and z-axis stabilizer for the Ender 3 Pro. With the use of a ball bearing, the z-axis stabilizer will support the top of the threaded rod while printing. Feel free to customize as needed. No extra pieces...

A basic filament guide for the Ender 3 S1 Pro that prints in one piece with not support.I made it because I got rid of the filament runout sensor and I needed a very simple guide so the filament does not get stuck wile printing.

This is a voron Printhead that is attached to a Orbiter and this is allowed to be placed on an Ender 3 / Ender 3 Pro / cr-10 Materials needed x8 M3x25 Screws x10 M2x8 Screws x2 40mm x 40mm x 10mm 24v side blower fan 40mm x 40mm x 20mm 12v noctua fan...

I designed this end-cap after waking up to a spool of filament on the floor that had popped over the lip of the holder mid-print. Lucky for me the job still printed but it could've been a lot worse. I designed this in Tinkercad. This is...

(and the solution seems to work for all filaments) I even contacted Makerbot support (yes, they are still responding), and asked for a guide on how to use filaments other than ABS. Their response was that this was an experimental printer and it only...

This is a simple rotating filament holder sleeve that fits over the stock ender 3 (pro) filament holder. The setup uses one bearing at the end of the holder and two to support the sleeve at the mount. The sleeve has flanged ends to stop the filament...

Remix from: https://www.thingiverse.com/thing:4441163 Ender 3 Pro Filament Guide Remix v.2 verbesserte Version. Habe bei meinem Ender 3 Pro alle hinzugefügten Teile aus ABS gedruckt. Mir ist aufgefallen das ich im Bereich Extruder sehr viel Abrieb...

Filament guide with run-out sensor for Ender 3 PRO when use Aluminum Upgrade Dual Gear Mk8 Extruder. ... Extruder upgrade: https://www.aliexpress.com/item/33041168934.html

This Bracket is for Creality Ender 3 Pro (2 cm)

Filament guide for the Ender 3 (Pro) - can be attached anywhere to the v-slot profile frame. ...I use it to guide the filament from the rear spool holder over the top frame and then down to the direct drive extruder.

Filament guide for the Ender 3 (Pro) - can be attached anywhere to the v-slot profile frame. ...I use it to guide the filament from the rear spool holder over the top frame and then down to the direct drive extruder.

A remix of Jack1961's Filament Guide and Runout Sensor Bracket: https://www.thingiverse.com/thing:3450311 This bracket fits an Ender 3 (standard, Pro or V2) and attaches using the existing screws on the Extruder assembly that connect it to the Z-Axis...

... is a stable filament guide for a 30mm ball bearing. ...The arm fits on every 20mm aluminum profile like the Ender 3 (Pro) Dies ist ein stabiler Filament Guide für ein 30mm Kugellager. ...Der Arm passt auf jedes 20mm Aluprofil wie beim Ender 3 (Pro)

So if you have an Ender 3 or an Ender 3 pro, you CAN have a foldable filament spool holder from the CR-6 SE! Maybe some filing is needed, because of tight fit. ...Use a 40mm M3 Allan screw with a nut to mount the holder with the mount and re-use the 2...

I printed this on my Creality Ender 3 S1 Pro and also printed on my elegoo resin printer. It was a llittle tight when printed with resin vs filament with the same settings so I uploaded a standard, tighter and looser version. ... The one pictured is...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 200 Infill: 90 Filament: PolyMaker PLA Black Notes: Printed with v high infill to ensure strength for weight of spools How I Designed This ===================...

This project started when I saw some upgrades for the Ender 3 Pro, and one of them was this filament holder. So I searched for this upgrade but all seemed that was a lack of something, or the cable holder hasn't good fit for my taste, or the filament...

... so that they are thight fit and they didn't need any glue. I also added guide pins so that filament won't jump out of the groove from the wheel.Here's video of how the rollers are turning while printing:https://www.youtube.com/watch?v=YY1DHYwU-EE