how to feed filament ender 3 3d models

Remix of https://www.thingiverse.com/thing:3129612 I modified the BearingRetainer to be double and have one side cut at 65º, to make it easier to insert and remove the filament. ... Requires a 608 bearing (Skate wheel bearing Black Sheep Black) and an...

... version). ...His original design had a rather thin base, which resulted in warping near the screw slots when the filament encountered minor resistance due to stress. ...To address this issue, I thickened the base to make it significantly sturdier.

Use standard 4mm OD PTFE tubing. ...Not too short to allow the filament sensor to move. You can use the side cutters in the holes on the back of the holder to rotate the holder more easily. ...(for print only support on bed)

A piece is added to be able to use the tool more comfortably.It allows us to hold the extruder so that we can change the filament more easily and with more care.Two pieces are printed at a time and then glued together.

A handy guide that mounts on the filament spool hook to gudie the cabel from a drier box. Make two copies and glue together with cyano acrylate. ...To install you need to remove the cap from the end of the spool holder, slide on the guide and then...

This is a simple filament guide I made because I did not like that the filament would rub against the Z-Axis Guide Rod when printing. To mount, all you do is remove the 2 screws beside the guide rod and slide the piece over. Once done, reinstall the...

To build this project, you will need: * A Z-endstop switch * A bearing * A Bowden tube Important note: If you find that your 3D model is oversized in Cura or Slic3r, be sure to scale it down by 10%. ...I've tested this and can confirm that it works...

One Piece Filament Support/Guide - Effortless Printing at Your Fingertips.

Filament guide for up. V2 - nuts. ...V1 - binder clip.

Filament should be accepted from below instead of above.

Filament Offsetter with Sensory Input v7.stl Model

Supports are not necessary with proper bridge settings, but if you do need supports, print with supports from the bedplate only, thoroughly remove all support material, and smooth the surface with a file to ensure the switch doesn't snag on any...

Spool holder mount for Sunlu Filament Dryer. ... Print x2, reuses M4 T-Nuts and screws from stock filament holder.

This filament guide holds the filament out from the printer 100mm and pushes it back about 50mm

A hook that holds the filament in place (better) use a short piece of 1.75mm filament as the pin

Remixed from another filament roller to prevent the filament from bending. Since I didn't have a spare wheel bearing or a screw, I decided to modify the design so I could print it without any extra parts. The wheel doesn't have the bearing...

... of two other creator's pieces. Thanks to micahjj, his mount was found here; https://www.thingiverse.com/thing:4915314 and Haduuuken, whose mount can be found here; https://cults3d.com/en/3d-model/tool/sv01-sv03-sv04-filament-runout-sensor-mount

... mounting system wasn't compatible with its new filament guide, but the design of the spatula guide's mount caught my attention. ...To solve this issue, I skillfully merged the two concepts to create a hybrid solution that fits perfectly on my printer.

... loose from the printer frame. ...I changed the mounting piece and combined it with the guide to make it much more secure. It is pictured in the orientation that it goes on the printer, but you need to print it upside down, like it is in the .stl file.

Bigtreetechbolt on filament sensor mount. use crazy glue to secure the wheel pin cap in place. easy to install. ...take the nut off top bolt push the bolt flush with the metal bracket than tap the mount on install bolt and nut..install sensor remove...

... loose from the printer frame. ...I changed the mounting piece and combined it with the guide to make it much more secure. It is pictured in the orientation that it goes on the printer, but you need to print it upside down, like it is in the .stl file.

Guides your filament to the extruder using a piece of PTFE bowden tube. This version doesn't need the adapter, but just holds the tube press-fit.</p><p>For best results, use TPU. ...It'll hold the tube snugly, and flex to get just the right angle...

I made this spacer because I could not find one that fit the spool on my printer arm. ...This has a larger hole to slide over the spool on the printer. I also made it a bit long so there is not a lot of side to side movement of the role of filament.

... the spindle of the Z-axis comes into contact with the filament. ...This can lead to the material becoming excessively greasy. And just because it's a blast to experiment and innovate :-) Design: https://www.tinkercad.com/things/vFJrTzQp7uq-z-axis-tube

Guides your filament to the extruder using a piece of PTFE bowden tube. This version doesn't need the adapter, but just holds the tube press-fit.For best results, use TPU. ...It'll hold the tube snugly, and flex to get just the right angle between your...

... for better support on the printer so that the clip doesn't keep falling down from the pressure of the filament as it is fed through during printing. ...I use a little piece of tape to hold the extended block to the printer upright and it works great.

Es un soporte para montar el sensor de filamento de la cr-10s en una Ender 3 y además sirve de guía de filamento a la salida del carretel. Yo lo usé en una Ender 3v2. Como opcional, para disminuir el rozamiento, agrandé el orificio de entrada con...

I've added a convenient opening that allows for hassle-free installation, eliminating the need to wrestle with threading filament through the piece and machine. To put it to the test, I ran a print at a moderate .2 resolution and a steady pace of 40...

... ...Installation involves removing two screws securing the Z-screw, then positioning the piece in place as depicted in the accompanying images. Utilize the included rubber component originally packaged with the filament clip provided by the Palette 2.

This small device helps protect the filament from contaminants such as dust.A piece of sponge, pre-lubricated with a small amount of alcohol, is inserted into the filter.Tighten the cable tie into the special recess located in the middle of the...