hp server power supply conversion 3d models
148854 3d models found related to hp server power supply conversion.thingiverse
Was making a 2nd 3D printer and wanted to use a Server power supply as it was cheap and very durable. ... Wanted to make a Shell to help Case it with Arduino Ramps 1.4 All measurements are as close to the real thing, Considering 0.1mm differences in...
thingiverse
This is a bracket to mount two HP server power supplies into a BTC-S37 mining case.
thingiverse
A replacement handle for an HP HSTNS-PR17 server power supply. ...(AKA the power supply for a HP DL360 G6, but should also fit similar models like the DL380 G6)
thingiverse
... ops. ...73 Paulo G0MUW, CT1EFL, F5VMJ Full build details on my Hackster account: https://www.hackster.io/pnjorge/hp-server-power-supply-case-64f438 Videos: https://youtu.be/KsLedhMzRkY https://youtu.be/M5qRzoQIgcs https://youtu.be/q8ZGHTefn3o
thingiverse
A clamp down mount for the HP 750/1200w power supplies. Print two sets. Holes for the clamp are printed to be tapped using a 1/4" tap. ... Use 1/4" machine screws to tighten the top clamp onto the bottom mounting plate.
prusaprinters
Recycle an old HP DL380 G2 server power supply into a bench/hobby power supply. Instructions After modifying your recycled power supply to be always on, just print, wire up female bullet jacks, and you have a tidy looking 12V 32A power supply. ...Hold...
thingiverse
Recycle an old HP DL380 G2 server power supply into a bench/hobby power supply. Instructions After modifying your recycled power supply to be always on, just print, wire up female bullet jacks, and you have a tidy looking 12V 32A power supply. Hold...
thingiverse
Simple cover for the exposed power connections for the HP server power supply (750W) that is commonly modified for RC charger usage. Provides separation of the + / - sides, and makes for a clean look. ... I attach this with a bit of "goo" type...
prusaprinters
Many people use the high-density hp server power supplies in the exterior christmas led lighting boxes. ... These models (2 pairs required per PS) allows you to mount them vertically inside a box (will mount in CG1500) using (4) ¼-20 bolts or...
thingiverse
When used in combination with my existing [HP power supply mount](https://www.thingiverse.com/thing:4605175), adds a second HP power supply mounted above one mounted on the lower one.
thingiverse
This should attach to the back of an HP server power supply like HSTNS-PL11 1200w and allow the power supply exhaust to exit while pulling in fresh air around it or from another opening. Scale to .5 for creality ender 3 I've included the blend...
cults3d
HP server power supply edge connector protector. For personal use only. Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that...
thingiverse
HP server power supply edge connector protector. <b>For personal use only.</b> <b>Attribution</b> — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but...
thingiverse
Bracket designed to hold an HP power supply with a wizard of wire breakout board, a Falcon Smart Remote, and a JBoards Power distro-8. All in a Harbor Freight .50 cal ammo box. Designed to print without any supports needed, you may get a little...
thingiverse
for those making a 24v power supply here is a mounting system that is easy to print. ... the front and cover are designed to print with no supports the back only needs supports for the stop points.
thingiverse
Remixed front panel from https://www.thingiverse.com/thing:4947889 to allow for small metal SPST On/Off switch. ... Thanks to pnjorge for a great design!
thingiverse
These are HP server power supply mounts. ... I use them with M3 bolts
prusaprinters
These are HP server power supply mounts. I use them with M3 bolts Category: DIY
thingiverse
Remixed from https://www.thingiverse.com/thing:2520995/#comments For use with HP Server DPS-800GB Power Supply on the 2020 extrusion. ...
grabcad
HP and I believe also Dell used these power supplies in 1U servers. They are readily available on Ebay and there are multiple companies that sell connectors for them so they can be used as a generic 12V power supply. This is a rough and dirty model I...
thingiverse
This bracket is used to mount an HP server power supply to the bottom of an Ord Bot. The power supply I used is a 750 watt supply part number HSTNS-PL18, but I believe the more popular 1200 watt supply may share the same dimensions and fit as well.
thingiverse
his is a bracket for mounting an HP Server Power Supply into a Bud Industries NBF-32022 enclosure. It uses two of the same 3D Prints mounted "facing each other". The bracket fits the HP 1200W/750W power supplies sitting in opposite directions, held...
thingiverse
This is a server supply holder for 2020 alumium profile.
thingiverse
Vertical mount for HP 750w and 1200w common slot power supplies. This does allow for some movement in the mount for easier adjustments. Mounting holes are for 6-32 or M4. I printed these in PETG, 20% infill, 3 walls. ...I would NOT recommend PLA...
thingiverse
See detials on how to do set them up as stand alone PSU's here (read carefully and be safe): http://www.rchelination.com/setting-hp-dps-1200fb-power-supply/ This thing is a mount I designed to attach one PSU to my new Hypercube 300 CoreXY 3D Printer...
thingiverse
Front case for DPS-600PB B and similar server power supplies to cover control pins and hold power connectors. Print Settings Printer: Tevo Tarantula ...
thingiverse
This is a front connector panel for server power supplies. It has 4 v 5V USB sockets,3 x 12V Power Pole connectors and 1 x 12V spring terminal connectors. See http://www.sadarc.org/xenforo/upload/index.php?threads/server-powersupply-mod.235/page-2...
thingiverse
Hakko T-12 soldering station mount for HP-460 server power supply upd. ...29.01.19 Fixed dimentions