huion pen case 3d models
242749 3d models found related to huion pen case.thingiverse
Customized version of https://www.thingiverse.com/thing:2562388 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2562388
thingiverse
Stand for no battery pen of HUION H430P graphics tablet for design. ...https://www.huiontablet.com/all-products/graphic-tablets/huion-h430p-4096.html
cults3d
A desktop stand / holder designed for the Huion PW100 battery free pen. ...The design supports both horizontal and vertical placement of the pen.
thingiverse
Pen holder for the PW201 Battery-free pen for the Huion H430P Drawing Tablet. Consists of the pen holder, along with an optional pen tip holder part that fits perfectly with the pen holder. ...printed with 10% infil, but can be printed with more if...
thingiverse
I have a Huion H1161 tablet and the pen holder that was supplied is a very poor fit. This is a replacement holder that fits on the original Huion base. The tags that connect the top and bottom together are 1.55mm thick and on my print the tags are...
cults3d
A minimal Huion pen mount that holds it with the tip upwards and the logo facing the front. Can be fitted to any flat surface with double sided tape. I originally designed it to fit to the right side of my monitor, but I don't see any problems to...
thingiverse
A minimal Huion pen mount that holds it with the tip upwards and the logo facing the front. Can be fitted to any flat surface with double sided tape. I originally designed it to fit to the right side of my monitor, but I don't see any...
thingiverse
This is a stand for a Huion **PF150** pen, the one distributed with Q11K drawing tablets. I'm not sure if this will work with Huion's other similar pens, but it shouldn't be too hard to adjust. I made this because I wanted a stand that holds the pen...
cults3d
Hi! ...It's my first project. Hope you like it and you find out this usefull. In my other thing you can find a Huion graphic tablet holder.
thingiverse
Hi! ...It's my first project. Hope you like it and you find out this usefull. In my other thing you can find a Huion graphic tablet holder.
sketchfab
This is meant to be a generic design of the typical digital pen. It is made in Fusion360 has no Textures and its not poly optimised at ALL. So have fun texturizing and optimizing it :) I might upload a baked version too someday. ... Use this pen for...
myminifactory
Pen Holder for HUION PW100. You will need two 8mm (diameter) x 1mm magnets
thingiverse
This is an improved replacement nib for the huion digital tablet pens. The OEM one is garbage and falls out of the pen, this one doesn't. ...
thingiverse
Supports are required for the regular mount for the screw holes. ...However they are not required for the tape mount. This pen holder should fit the Huion Pw507 pens and mount directly to the side of your desk for easy access.
thingiverse
Redesign of the Huion PW-517 pen used with the recent Kamvas screen tablets. Just over 1cm thick depending on printing settings and almost as long, everything should fit inside if wash 'n' cured properly. ... NOTE: use the 3mf instead of the obj, it...
thingiverse
I made this simple model to hold my Huion HS64 vertically against the wall at my desk. It can hold the tablet and pen without taking too much space. The pen hole is not too tight, allowing it to move a bit. If your printer has a moving bed, like...
thingiverse
I also made a little hole (tunnel) to remove the nib of the pen, but at first it didn`t work. So I removed the pull tab of a soda can and removed the part with the small hole (where it connects to the can) and glued this with a small offset onto the...
thingiverse
Simple pen holder for hs64 graphics tablet. ... simple and fast to print
cults3d
... small holder will keep your Wacom pencil always at hand and without risk of falling down. ...There are 2 versions, one for small and old assemblies (CTH-460) and one for new models. Compatible also with pencils from other brands like Xp-Pen or Huion.
thingiverse
This perfectly fits a Huion pen. It might fit a Wacom cintiq pen. But it could certainly be adapted with some shuffling of dimensions. Just tack or glue it to the top corner , and stop losing that damn pen! When printing. The top should face down, so...
thingiverse
Pen/Stylus holder for Huion Battery Pen. The base is a compartment to hold up to 6 replacement Nibs. ...
myminifactory
Pen/Stylus holder for Huion Battery Pen. ...The base is a compartment to hold up to 6 replacement Nibs.
myminifactory
Pen holder for huion h610 battery type pen. It has an opening for holding the pen in vertical position If you find my models useful, please consider tipping. ...It helps me to allocate more time for making models.
thingiverse
It allows you to have the pen on the monitor instead of in the pen case, on the table or the pro 22 pen stand.. Please read installation. You need: Orbit front and back plate printed out(backplate is actually front plate!). 2 m3 screws...
cults3d
It allows you to have the pen on the monitor instead of in the pen case, on the table or the pro 22 pen stand.. Please read installation. You need: Orbit front and back plate printed out(backplate is actually front plate!). 2 m3 screws (8-20mm...
myminifactory
Thumb rest locator for the Huion HS64 graphic tablet pen. I printed mine from flexible filament. It slides on from the back to stop just below the buttons. Helps inform the fingers where the buttons are located without having to look down. |...