hypercube evolution 2020 3d models

Suporte para probe PL08N. ...É instalado atrás do carro, por cima dos parafusos das correias.

I've created a simple spool holder using a tried and tested design, featuring 8mm rod and 608 roller bearings commonly found in skateboards, rollerskates, etc. The SCAD file for crafting a custom spool clamp to your precise specifications can be...

Thanks Scott for this amazing find on Thingiverse - https://www.thingiverse.com/thing:2254103! This part is super helpful in setting up my Y-carriage and may even boost X/Y/Z carriage accuracy. To get the most out of it, I need to print two copies of...

I'm having trouble getting the IGUS clone RJ4JP to work right, and sometimes the bearing slips up or down. ...It works really well otherwise.

<p>Da mein Diamond Hotend mit seinem Bowden und dem Y-Endstop am HEVO kollidierte, habe ich einen neuen konstruiert der nicht mehr im Weg ist.</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>Anet A8</p> <p class="detail-setting...

I've found that large leveling knobs are far superior to small ones, so I designed one specifically for the HEVO. The nut fits extremely tightly within the knob, which is exactly how it's intended. You have two options: either screw it into place...

Mounting Brackets for LED Lights Available on Amazon. These brackets require M5 screws for installation. ... View the product on Amazon here: https://www.amazon.com/gp/product/B013BBLU44/ref=oh_aui_detailpage_o06_s01?ie=UTF8&psc=1

This is the Bowden Hotend mount for the upcoming all-aluminum HEVO SML Fusion RC upgrade kit. It follows the 25mm^2 Dwell Pin / M3 screws in front and center screws that mount from the back plate of HEVO's original design. The fanduct should not...

I adored the concept of modifying the cradi's Y flag and eagerly printed and utilized one. A sudden epiphany struck me - if I extended the flag slightly, I could invert the Opto-sensor, positioning its connector beneath the extrusion for a sleeker...

Compact Z-Screw Bracket designed for users with shorter Z-screws than their corresponding Z-Rods.

First off: thanks go out to Scott for an amazing job! I appreciate it. However, there were a few issues with his extruder parts that really got under my skin. One of them was the fact that the insert brass nuts would pop right out when tightened too...

E3D Titan Aero mount --- Using a Titan Aero adds width to the X assembly and reduces X travel compared to standard design; the amount depends on motor and fan used. With 20.7mm motor and 7mm fan I am limited to 295mm of travel in X with approx 1.5mm...

This is an adaptation of Duke_S's leveling foot designed to fit over the printed corners of melnikod's electronic enclosure. They slide up into the corners and secure with M5 bolts and T nuts. It was found that placing the T nuts in the printed...

A Customized HEVO Mount Featuring a Chimera/Cyclops Design. ... This innovative mount is equipped with several essential components: * A Built-in BL Touch Module for precise calibration * A Standard Fan Duct for optimal airflow * A Standard Fan Mount...

The spool holder operates effectively with spools that are up to 85mm in width. It functions exceptionally well in conjunction with my custom MK3 Hevo extruder. ...To install this spool holder, you will need: Two M5 T Hammer Nuts for a 3030 extrusion...

I tried to install a Hemera on my HEVO 445, but soon discovered that there was too much wiggle room in the linear rod setup to handle the weight. I decided to attach my Y axis rails directly to the 3030 extrusion and work from there instead. ...My...

Reconfigured the original design for use with a Dragon hotend. All hardware is the same except for the mounting screws for the hotend, this uses 4x M2 screws. Also I recreated the fan duct from scratch for a cleaner assembly. I will not be printing...

This bracket originates from Scott's design but features a reduced offset of 12.5 millimeters, specifically smaller than Scott's mini at 15 millimeters. ... It enables the mounting of a 328-millimeter MKx bed with 320 millimeters between fixing holes...

I created a set of custom bed leveling knobs for the HEVO, but discovered that the original design's shaft was too long due to using overly strong springs. To rectify this issue, I modified the design by removing the bottom half of the shaft. Kudos...

I've updated the Extruder Mount for the E3D V6. It now features two larger holes for endstops and has been modified to accommodate sensors. ...Have a great time using this new design!

I don't know if my 3030 aluminum extrusions are different, but the original y endstop bracket with the 8mm "Bulge" didn't fit in my extrusion. ...Uploading in case someone else finds this useful.

1. Insert a BL Touch shim with a 4mm height for the print. 2. BOM Includes M3 bolts and nuts, one brass threaded insert M3, and a 4x dowel pin. 3. Consider using fan duct designs from Thingiverse: https://www.thingiverse.com/thing:2732387 or Berd...

This is an optical endstop mount designed to work seamlessly with stock 100mm extrusion spacing, specifically tailored for use with Warham's upgraded XY carriage. It features a clever design that allows the wire to pass through and exit on the side...

Customized version of https://www.thingiverse.com/thing:2448362 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2448362

I have modified the following: 1.) Added mount for 40x40mm fan. I currently am using a 40x40x28mm fan. 2.) Modified the BLTouch Mount to allow the wires to be run up through the center. 3.) Added zip-tie slots for wire management. 4.) Added support...

Hello, I created some Silicon Bumpers for my Bed using the 15mm Bed Bracket, but they fit mostly with the 20mm Bed Brackets. ... I utilized this silicon:...

Modifications are currently being made, with publication pending alongside the development of 3D printing technology.\r\n\r\nUPDATE:\r\n\r\n4040-motor-add.stl - This modification is designed to reinforce the engine mount. We are now installing the...

This compact adapter mounts directly onto the carriage, securing my cables in place with a mesh sleeve that's significantly smaller than the hard cover designed for the hotend. The adapter slips snugly into the clamp, while a zip tie beneath keeps...

We offer Support for igus' T8 system.

We provide support for both T8 and T10 power supplies for our polyurethane square track.