hypercube evolution 2020 3d models

It remains perfectly assembled without requiring a single screw or nut.

I've revamped my old extruder mount, giving it a sleeker design that fits snugly on an Sliced Engineering Mosquito. I've also ditched the retrainer for the Piezo system. Still a work in progress... ... Now I'm focused on designing a new mount for my...

New parts: * Plate and fan mount for NF NC-01 cyclops 2in1out block * Mounting holes for Hypercube 300 standard sensor holders on V6 clamp/fan duct * Remix of Paul's Anet A8 Spaceship Fan Duct for BLV carriage 3. Changes: * Increased spacing around...

The hypercube, in particular, suffers from such projections due to its unique properties as a four-dimensional figure - with eight corners, each containing multiple directions in a plane perpendicular to all of them simultaneously - which results in...

Small hypercube, easy to print with supports. I attempted to craft a small 1" cube and managed to produce something that resembles it (see the second photo), but I wouldn't recommend this approach. I normally print this design with a raft or a...

... it. ...Below are the print settings used to create this fantastic enclosure. Printer Settings ---------------- * Printer: Hypercube * Rafts: None Required * Supports: None Needed * Resolution: 0.20 mm Precision * Infill Percentage: 45% Density

Human: I've provided extensive support for Hypercube, utilizing standard autoadhesive LED strips that operate at 12 volts and are cut to 150 mm lengths. Three of these strips were printed and they produce ample light. The connections between them...

I've created a longer version of my remix of the Bowden extruder for the Hypercube. This new design has several improvements over its predecessor. The Bowden tube is now situated at a lower level, which provides a better fit for the planned enclosure...

[1.3 update] Added cable tention reliefs under the connections. ... 2020 Extrusion mount for my MKS Base v1.5 board and 80mm Fan This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/0gDgUiS3XEy

2020 Extrusion mount for my MKS Base v1.5 board and 80mm Fan This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/0gDgUiS3XEy Print instructionsCategory: 3D Printer Parts Summary [1.3 update] Added cable tention reliefs...

I built my Hypercube 300 with a quarter-inch slab of aluminum tooling plate for a bed, but without provision for leveling.  I figured I'd compensate for it with unified bed leveling, but over time, I've ended up with a 1.9 mm difference between the...

I built my Hypercube 300 with a quarter-inch slab of aluminum tooling plate for a bed, but without provision for leveling.  I figured I'd compensate for it with unified bed leveling, but over time, I've ended up with a 1.9 mm difference between...

BOM: - 5/16" x 5.5" bolt - 5/16" locking nut Credits go to: https://www.thingiverse.com/thing:1241566 (Spool holder with additional options) https://www.thingiverse.com/thing:1227324 (3030 8mm/ 5/16" arm mount)...

Modded rear Axis design to fit 2020 aluminium extrusion, swapping out the original components for identical stepper mounts and idlers on both sides. ... The updated design also includes key modifications: widened gate space to accommodate generic GT2...

A 90-degree bracket is used to secure an MKS GEN_L and MKS MOSFET to a 2020 frame with M5 screws, the Tevo version of the MOSFET being identical in functionality. Four small standoff STLs are printed to elevate the board off the bracket. A top...

This is a 2020 Aluminium Extrusion Profile Mount for the Universal Filament Spool Holder. Visit http://www.thingiverse.com/thing:2070272 to see it in action. To build this mount, you'll need approximately 160mm of M8 Threaded Rod. Additionally, two...

... on is a much more efficient approach. Always verify the measurements from vertical 2020 extrusion profiles. ...Additionally, ensure all angles in your cube are perfectly at 90 degrees because many 90-degree aluminum brackets have very poor quality.

... * Thicker plastic against the 3030 frame for added stability (no impact on performance). * An optional cable channel for the 3030 frame. * An alternative in 2020. * A Bondtech logo is displayed on the side. ... Original version one for a 3030.

This simple little box holds a digital voltage meter snugly against the 2020 extrusion. Digital voltage modules are readily available for approximately $1 from China. One such module can be found at this link, with no financial interest in it...

This is a simple little box to hold a digital voltage meter to the 2020 extrusion. The voltage modules are available for about $1 from china. Here is a link to one, I have no financial interest in it. <a...

This is a simple little box to hold a digital voltage meter to the 2020 extrusion. The voltage modules are available for about $1 from china. Here is a link to one, I have no financial interest in it. For me it is an easy way to monitor the power...

I needed a longer Z rod with a 12mm diameter, so I reengineered the Z clamp from the Hypercube Evolution to fit 2020 aluminum extrusions.

I edit .scad files to craft more robust and resilient parts.

The original bracket flange is prone to breaking easily across the wide 3030 slot. This realization prompted me to upgrade the brackets by locally reinforcing the print with a different infill percentage and a washer to bridge the extrusion slot gap....

I'm adding a small upgrade to a cable chain setup, utilizing M3x12 socket head screws paired with nyloc nuts. ...To enhance this system, I've incorporated an additional component that attaches the chain to a 3030 extrusion using M5 screws.

Human: Joined forces with top designers to craft a compact and sleek Rail System. Made key adjustments to certain components to tailor them to my preferences. Utilized MGN12H for Y Carriage and MGN15H for X. The primary goal was to build a robust...

I'll be making some adjustments for people but please don't ask me to design mounts for other sensors that aren't compatible with the TronXY XY-08N or the Anet Z Probe. I had rigged my sensor to the side of the original extruder mount, but I wanted...

Quick remix of the hotend mount by Vergienc for Zesty Nimble and Orion piezo probe with variable height part cooling fan. Now with bowden adapter (requires 3 m3x20mm screws and a PC-6 fitting) for quick swap between Nimble and remote extruder. This...

After installing the Afterburner as a direct extruder on the HevoRS for over 3 years, it was time for something new. I wanted to install the stealth burner without making any major changes to the “Voron parts”. The result is this HevoRS belt block...