hypercube tech2c 3d models

The engineer secures the wiring for the hypercube's x/y carriage using a sturdy 1/4-inch P-clamp, known as an Adel clamp. ...This clever tool provides just the right amount of slack, allowing the wiring to pivot smoothly and effortlessly throughout its...

... align easily. ...The clever nut trap design eliminates the need for multiple tools, streamlining the process. I printed mine on my Hypercube at a .1 layer height and 50% infill, and it turned out great; you can try .2 or better with good results.

... Noise from Vibrations. To Address the Issue, a Hybrid Solution is Formed by Merging the HyperCube E3D Clamp and a Fan Duct into a Single Unit. ... 09/24/17 - an Extended Version of this Design has been Created to Rectify a Missing Radiator Rib.

This was a Lightning-Fast Project to slash airflow around my printer as the XY Carriage run is inside the frame on the hypercube I had to think outside the box. The Channel for the part is 5mm thick and the fastenings are M5x20. ... Mirror the part in...

Update 12/03/17 As requested, I have also added mounting slots instead of just holes Extended the HyperCube fan duct by 10mm, as requested by RalphVigg. Print instructionsLicence: Creative Commons - Attribution - Non-Commercial - Share Alike...

Quick OpenSCAD hypercube code that just works. Rushed into existence, but full of parameters for the eager designer. Don't even think about trying this with a cheap printer - it needs good bridging capabilities to come out right. ...Not saying it can't...

After upgrading to a HyperCube 300, the bed mounts didn't fit. I didn't find any that worked for my bed, so I designed a new one from scratch with Parameterization.</p> <p>The attached STL gives about 27mm from the edge of the 2020 extrusion. ...Check...

I designed this basic GoPro mount to enable me to attach my GoPro to my HyperCube Evo. The name reflects its purpose. This design should be compatible with any 3D printer. It's specifically made for M5 screws and T-nuts. ...I salvaged the screw from a...

This is a remix of the Hypercube Evolution by SCOTT_3D I have not printed and tested this, just a quick remix done in TinkerCAD XY idlers are just raised/thickened a bit to avoid collision with the corner of the 4040 profile.

... tensioners, just like in the original design. You need to print: 1x titan carriage 2x LM10LUU clamp 1x belt clamp More info, updates and mods can be found in my Hypercube repository: https://github.com/diegotrap/hypercube Category: 3D Printer Parts

This is an upgrade to your current Dremel setup featuring a "slot-in nuts" mount originally used on the Hypercube 3D Printer X Carriage. ... Edit : I designed this specifically for the Dremel 3000, but it may also work with clones or other rotary...

... functionality. To print this new X carriage: 1. Print 1x titan carriage 2. Print 2x LM10LUU clamps 3. Print 1x belt clamp For more information, updates, and modifications, visit my Hypercube repository at https://github.com/diegotrap/hypercube

This is the custom bushing I designed for the hypercube printer head to accommodate an 9.8mm carbon fiber rod. ...To ensure a snug fit, I specified a 0.5mm nozzle and factored in a significant tolerance for printing layers as thin as 0.2mm.

Revised Y axis Endstop designed to fit a standard 2 pin endstop on a RAMPS board, the original 3 pin endstops didn't work for me because I built my hypercube with a repurposed RAMPS board opposed to a duet wifi. ...Fits 1/4" or 5/16" rod

Hypercube X axis endstop designed to snugly fit and snap onto 3/8" (6/16" | 9mm) carbon fiber rod, designed to holster a traditional 2 pin endstop (Works well with RAMPS board as RAMPS only have 2 pinouts opposed to a board with 3 pinouts for...

Very simple corner brackets for the top of a Hypercube Evolution. Just print four of them and you are good to go! ...The holes are sized for M4 bolts but I used M3 bolts plus a washer and that worked well also.

This thing is designed for use with the Hypercube Evolution, if you want to incorporate a mechanical stopper. To assemble it, you will also need: 1 M4 nut, 1 spring, 2 washers, and 1 M4x20-50mm cylinder head screw. ...Take advantage of this opportunity...

I needed this tall foot to get some space for fans and components on my Hypercube Evolution. ... For the screws M5 are used and the squash balls are from...

The Hypercube 3D printer's Z axis carriage gets an upgrade with the LM10LUU, a long linear bearing that measures 10mm in length. ...To put it to good use, simply pair it with this 10mm Z axis mod available at http://www.thingiverse.com/thing:1950819.

... springs could definitely be made more pliable. If anyone is interested in refining this concept, I'd appreciate receiving a copy of the STL file. This design attaches easily to the extruder's bowden mount and can be used on the HyperCube printer.

HyperCube 3D Printer XY Joiner. Y Axis LM10UU and adaptive clamp holder. X Axis 10.25mm rods etc. X Axis 8.25mm rods etc. 20T tooth pulley Need to M3 Screw... Some size UPDATED! ... Add new X axis to 8.25mm

The X-axis endstop is 10 mm in diameter, which matches the dimensions for X-axis carbon-fiber tubes specified for the Hypercube 300. The Y-axis endstop is 8 mm in diameter, matching the dimensions for Y-axis steel rods on that printer model. ...Change...

The X-axis endstop is 10 mm i/d and the Y-axis endstop is 8 mm i/d; these correspond to the dimensions for the X-axis carbon-fiber tubes and Y-axis steel rods specified for the Hypercube 300. Change and rerender the OpenSCAD files if you need...

All parts are newly drawn in accordance with the well-known Hypercube, but maximally massive and the Z intake is almost integrated as a whole. The BOM can be largely taken over from the original. Only the X waves are in 10mm and not like in the...

The machine is built upon the robust foundation of the Hypercube Evolution and enhanced with high-performance Hiwin MGN12(H) linear rails and a direct drive BMG extruder. To ensure everything fits snugly within the frame, minor adjustments were...

I wanted to modify the hypercube printer bed supports. ...But no scad files.</p> <p>Recreated in openscad, made parametric</p> <p>Modify offset value to lower the position of bed mount arm.<br/> NB make sure to leave room for the head of your tslot...

I designed some mounts for my hypercube evolution 24V-Powersupply to secure it on the 30x30-aluminum-profile-frame. I chose this one from Aliexpress:...

The Z carriage got a minor overhaul.\nQuality lm8uu bearings were installed, leaving almost no play.\nPrint Settings\nPrinter: \nThe HyperCube handled the job.\nRafts: No raft was used.\nSupports: No supports were required.\nResolution: A 0.2mm...

Drop-in replacement for the original hypercube extruder mount to use E3D Chimera or Cyclops. It lacks a sensor mount since I employ one mounted on the cooler fan, but if anyone desires a specific one, I can create it. This mount eschews a brass...

I've uploaded two versions of a Simple Hypercube fan guard for 40mm fans, complete with models featuring 1mm and 2mm standoffs. If you're planning to print this design, don't hesitate to leave a comment if you encounter any issues. For optimal...