hypercube 3d models

Air Duct for the TaoTronics 5L Humdifiert (see Picture) I could not let me run on high or moisture would build up on surfaces below it. The Air Duct lets the fog travel i longer distance an mixes it with air - now it work even on high. Print...

... under the cradle that allows a wire tie up to 6 mm wide by 2.5 mm thick to pass through. This thoughtful design feature makes it easy to manage cables with varying diameters. Check out my HyperCube printer at http://www.thingiverse.com/make:272257.

Exhausteur pour aquarium/bassin Pour tube pvc diamètre 25 mm Tube diamètre 4 mm pour raccordement arrivée d’air Le tuyau d’arrivée d’air passe dans le tube pvc Print Settings Printer: Hypercube evolution Rafts: NoSupports: No Resolution: ...

Tailored specifically for use on a Hypercube Evolution or any other 3030 profile system, this enclosure offers versatility and convenience. Key features of the design include a snap-fit lid that securely fastens without the need for additional...

... and should be printed open side up which requires no support. My webcam is now happy to not have dust in its eye :) Print Settings Printer: HyperCube Rafts: No Supports: No Resolution: 0.1mm Infill: 50% Filament: Hatchbox PLA Category: Computer

I wanted to re-use the PSU from a Tevo Tarantula on a new Hypercube, unfortunately the S-300-12 PSU is nothing like the supply in the BOM. This is similar to the original design but moves the switch to the outside of the printer and has the correct...

Direct drive with BMG and piezo orion, pancake 25 or 28mm, for NGEN caution : the chain holder is higher, because it's specific to my HEVO 3D live view : https://a360.co/2ZaA3Uh 09/07/2020 : STEP and F3D files added, carriage renforced 18/07/2020 :...

Remix of https://www.thingiverse.com/thing:599562 Original design was for so called Full Graphics LCD aka 12864 but I had to adopt it for classic 2004 LCD so called Smart Controller Through hole for the screwdriver (hex alien key) was introduced so...

... fits non sleeved cards. I might revisit this and make a sleeved version if there is demand for it and i feel like it. :) Print Settings Printer: Hypercube Evolution Rafts: No Supports: No Resolution: 0.2 Infill: 15 Filament: Amazon Basic PLA Black

Everything is designed to use M3- screws and nuts. As a fan mount, I used this design: https://www.thingiverse.com/thing:2449326 Print Settings Printer: Hypercube Evolution Rafts: NoSupports: Yes Resolution: 0.2 mmInfill: 70 % Category: 3D...

Thanks to phili76 for original design (and big ups for providing STEP files), unfortunately center hole for some of the steppers I have here were little too tight. I've simply increased centre hole (by 2mm in diameter) to 24mm to accommodate these...

I was after an easier to print version of KawClerics great looking goal markers. I'm sure the origionals look better but my garage is cold this time of year and printing anything with that level of detail becomes a bit of challenge! This is the main...

I wanted to use Sherpa mini and Trianglelab Dragon on my Hypercube evolution. But i coudn't find the mount for it. So I've decided to give it a try and make my own. The mount plate for sherpa/dragon has no space for end stops, if you want use them...

... the E3D V6 Hotend which has a Noctua active fan. The printer is extremely quiet. I use 8mm brass bushes with graphite bearings as my lubrication. Before I will soon convert everything to a Hypercube Evo, I wanted to share my ideas here first.....

... on an Anycubic photon dlp printer. I remixed the remix by closing the holes and setting an orientation to print on my HyperCube Evolution. ... I've added "angel_cat_Remix3.stl" which adds a ring to the design so it can be hung as an ornament.

Depending on your 3D printer tolerance, this prints fairly precise fit on my Hypercube printer with 0.4mm nozzle @ 0.3mm layer height. But if it doesn't fit nicely or you want to edit further for say LM8UU (shorter variant), you could edit the...

... are tutorials online to show you how to solder a button matrix together. Print Settings Printer: Hypercube EVO Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 200 Infill: 20% Filament: Monoprice PLA+ White + Blue Category: Electronics

Depending on your 3D printer tolerance, this prints fairly precise fit on my Hypercube printer with 0.4mm nozzle @ 0.3mm layer height. ...But if it doesn't fit nicely or you want to edit further for say LM8UU (shorter variant), you could edit the...

Designed in response to a post from the unofficial hypercube group on Facebook, I encountered issues with prints that weren't always attributed to "Z" banding problems. The culprit turned out to be the weight of the heatbed setup, which is now...

As a basis I used: https://www.thingiverse.com/thing:2732387 Titan Aero head mount for Hypercube Evolution + Addons by Asphyth The original Titan Aero mount was facing the wrong way for my setup, so I mirrored it. That worked fine. Then I tried...

This is my remix of the Hypercube Evolution by Scott_3D, where I've amplified the height at the top and bottom to enable easy enclosure printer construction. To upgrade the X and Y carriage, I've opted for linear rails MGN12, while keeping the belts...

This is a fully self-designed 1.3 meters high lighthouse created in Fusion 360 and printed on a large Hypercube with 0.2 layers - it took quite some time to print this model. I discovered several pictures of a lighthouse in Gotland, Sweden that...

The LM2596 can be found here: https://www.amazon.com/gp/product/B01GJ0SC2C/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 A digital voltmeter is available on eBay at this link:...

It's being utilized to power a HyperCube evolution with a 300mm bed that demands approximately 500 watts of power when both the bed and hotend are in operation. Additionally, a 5v power supply has been included to energize my Duet3D board and a...

... For instance, in my Hypercube 300, a Z-axis rod mount is right about where I want to put a Raspberry Pi Zero 2 W to keep it close to the main control board. For whatever it's worth, this is also my first design brought to fruition with FreeCAD.

This object is inspired by the concept of hypercube, a geometric notion where it serves as an n-dimensional analogue to a square (n = 2) and a cube (n = 3). It's a closed, compact, and convex shape made up of groups of opposite parallel segments...

And i did. I hope you like it! Supports are a bitch to pull out the mouth, but its worth it! Ill add more pictures when its finished and painted, also i had some extrusion problems as you sure can tell from the pictures. Print instructionsCategory:...

I made these bed spring cups for my Hypercube Evolution build. They are similar to the ones I made for my I3 (<a href="https://www.thingiverse.com/thing:2422944">https://www.thingiverse.com/thing:2422944</a>), but the springs I bought for my new...

I was unable to find a cable organizer or management system like the ones used in IS Racks, so I designed one to use on my Hypercube Evo base. The sizes for this design are as follows: Base Section: - The base measures 100l x 30w x 20h (with an...

My original plastic parts broke after being in the sun for a few years. Print Settings Printer: HyperCube Rafts: No Supports: Yes Resolution: 0.1mm Infill: 80 Filament: PolyMaker PLA White Notes: Bracket needs supports. ...End caps need to be...